Maintenance - Scheppach 7906100718 Originalbetriebsanleitung

• Do not use worn or ill-fitting sockets or extensions,
as this is likely to cause a substantial increase in
vibration.
• Select, maintain and replace the consumable / in-
serted tool as recommended in the instructions
handbook, to prevent an unnecessary increase in
vibration levels.
• Sleeve fittings should be used where practicable.
• Support the weight of the tool in a stand, tensioner
or balancer, if possible.
• Hold the tool with a light but safe grip, taking ac-
count of the required hand reaction forces, because
the risk from vibration is generally greater when the
grip force is higher.
Additional safety instructions for pneumatic power
tools
• Air under pressure can cause severe injury:
- always shut off air supply, drain hose of air pressu-
re and disconnect tool from air supply when not in
use, before changing accessories or when making
repairs;
- never direct air at yourself or anyone else.
• Whipping hoses can cause severe injury. Always
check for damaged or loose hoses and fittings.
• Cold air shall be directed away from the hands.
• Do not use quick-disconnect couplings at tool inlet
for impact and air-hydraulic impulse wrenches. Use
hardened steel (or material with comparable shock
resistance) threaded hose fittings.
• Whenever universal twist couplings (claw couplings)
are used, lock pins shall be installed and whipcheck
safety cables shall be used to safeguard against
possible hose-to-tool and hose-and-hose connection
failure.
• Do not exceed the maximum air pressure stated on
the tool.
• For torque-control and continuous-rotation tools, the
air pressure has a safety critical effect on perfor-
mance. Therefore, requirements for length and dia-
meter of the hose shall be specified.
• Never carry an air tool by the hose.
Start-up
• Screw the included plug nipples (4) into the air con-
nection after first wrapping the thread with 2–3 lay-
ers of sealing tape (not included).
• Attach the required plug-in attachment to the square
intake.
• Set the correct direction of rotation on the pivot bolt
(11) :
R = counterclockwise / remove screw,
F = clockwise / tighten screw.
• Attach the plug-in attachment to the screw head.
• Activate the trigger (2) .
Note: the connection to the compressed air source is
established through a flexible air hose with quick con-
nector.
The ratcheting screwdriver will perform best when
used with an LW 10 mm air hose.
After initial use
Once the task has been finished the equipment must
be disconnect from the compressed air supply (3) .
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Maintenance

Following the maintenance information specified here
will ensure a long service life for the product and trou-
ble-free operation. Your ratchet screwdriver working
properly for a long time requires daily lubrication.
You may choose from the following options:
With an oil-fog lubricator
A complete maintenance unit includes an oil-fog lubri-
cator and is attached to the compressor.
Manually
Add 3–5 drops of speciality tool oil to the compressed
air connection before every use. If the compressed
air tool is not being used for several days, add 5–10
drops of oil to the compressed air connection before
switching it on.
• Always store your compressed air tools in dry
rooms.
Cleaning and Care
• Never clean with liquids such as petrol, solvents or
water.
• Do not allow liquids to enter the tool.
• Only clean the tool with a dry cloth.
Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types of
material, such as metal and plastic. Defective compo-
nents must be disposed of as special waste. Ask your
dealer or your local council.
13 І 64