Scheppach 7906100718 Originalbetriebsanleitung Seite 11

• Maintain the device carefully. Check that moving
device parts are working properly and move freely.
Check for any parts that are broken or damaged
enough to detrimentally affect the functioning of the
device. Have damaged parts repaired before using
the device. Many accidents have their origins in
poorly maintained devices.
• Switch the device off if you do not use it anymore.
• Always wear personal protective equipment and sa-
fety glasses. Wearing personal protective equipment
such as dust mask, non-slip safety shoes, safety
helmet or ear protectors, depending on the type of
air tool and its application, reduces the risk of inju-
ries.
• Check the connections and supply lines. All mainte-
nance devices, couplings and hoses must be equip-
ped to meet the pressure and air amounts specified
in the device specific values. Pressure that is too
low influences the functioning of the device; pres-
sure that is too high can cause damage to property
and personal injury.
• Protect hoses from kinks, constrictions, solvents and
sharp edges. Keep hoses away from heat, oil and
rotating parts.
• Make sure that the hose clamps are always tightly
fastened. If the hose clamps are not tightly fastened
or are damaged, the air could escape uncontrollably.
• Replace damaged hoses immediately. A damaged
supply line may result in the air hose flapping about
and may result in injuries.
• If the power cable of the appliance is damaged, it
has to be replaced by the manufacturer or its service
department or a similarly qualified person in order to
avoid hazards.
• Do not use the device when tired or under the influ-
ence of drugs, alcohol or medications. One moment
of carelessness when using the device may result in
serious injuries.
• Do not directly inhale the exhaust air. Keep eyes
away from exhaust air. Exhaust air from the air tool
may contain water, oil, metal particles or contami-
nants from inside the compressor. This may damage
your health.
• WARNING! CAREFUL WHEN PUTTING THE TOOL
DOWN! Always put down the device so it does not
come into contact with the trigger. This could po-
tentially result in accidental activation of the device,
which again could result in hazards.
• Only use suitable accessories. These may be
purchased from the manufacturer. Using non- OEM
accessories may result in hazards.
• Only use filtered and regulated compressed air.
Dust, caustic vapours and / or moisture may dama-
ge the motor of the compressed air tool.
• The hose must be designed for pressures of at least
6.3 bar or 125 PSI, but at least 150 % of the maxi-
mum pressure generated in the system.
• The tool and supply line must be equipped with a
hose coupling to completely release pressure when
disconnecting the coupling hose.
• DANGER! Avoid contact with live lines. This device
is not insulated against electric shock.
• WARNING! RISK OF INJURY! High working pres-
sures can give rise to recoil forces that under certain
conditions can result in danger from continuous loa-
ding.
• If you are inexperienced in the use of this type of
device, you should seek training on how to handle it
safely.
• WARNING! DANGER OF STABWOUNDS! Do not
treat an injection as a simple cut. A high pressure jet
may inject toxins into the body and cause serious
injuries. If the spray is injected into the skin, seek
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
medical help immediately.
• Do not modify this device in any way without the
manufacturer's approval.
• Only use the compressed air unit with the specified
pressure (6.3 bar).
• Disconnect the compressed air unit from the air sup-
ply after each use and when not in use.
• Do not use the compressed air unit if it is not air
tight or in need of repair.
• Never connect the compressed air unit to an air ho-
se with pressure exceeding 6.3 bar.
• Keep your working area clean and well lit. Untidy or
poorly lit working areas can result in accidents.
• Doing so will allow you better control of the device,
particularly under unforeseen circumstances.
• WARNING! Only have the device repaired by qua-
lified specialist personnel using OEM spare parts.
This will maintain the safety of the device.
• Keep children and other persons away from the de-
vice during use. Distractions can cause you to lose
control of the device.
• Wear suitable clothing. Do not wear loose clothing
or jewellery. Keep your hair, clothing and gloves
clear of moving parts. Loose clothing, jewellery or
long hair can become trapped in moving parts.
• Put down trigger and device in the event of unex-
pected compressor failure.
• If possible, use a condensate trap or regularly drain
the hoses and pipes of condensate (water) before
and whilst using compressed air units.
• ATTENTION! An undersized compressed air system
may minimise the efficiency of your device.
• For multiple hazards, read and understand the safe-
ty instructions before installing, operating, repairing,
maintaining, changing accessories on, or working
near the assembly power tool for threaded faste-
ners. Failure to do so can result in serious bodily
injury.
• Only qualified and trained operators should install,
adjust or use the assembly power tool for threaded
fasteners.
• Do not modify this assembly power tool for threaded
fasteners. Modifications can reduce the effectiven-
ess of safety measures and increase the risks to the
operator.
• Do not discard the safety instructions; give them to
the operator.
• Do not use the assembly power tool for threaded
fasteners if it has been damaged.
• Tools shall be inspected periodically to verify that
the ratings and markings required by this part of ISO
11148 are legibly marked on the tool. The user shall
contact the manufacturer to obtain replacement mar-
king labels when necessary.
Projectile hazards
• Failure of the workpiece, of accessories or even of
the inserted tool itself can generate high-velocity
projectiles.
• Always wear impact-resistant eye protection during
the operation of the assembly power tool for th-
readed fasteners. The grade of protection required
should be assessed for each use.
• Ensure that the workpiece is securely fixed.
Entanglement hazards
• Entanglement hazards can result in choking, scal-
ping and / or lacerations if loose clothing, perso-
nal jewellery, neckware, hair or gloves are not kept
away from the tool and accessories.
• Gloves can become entangled with the rotating
drive, causing severed or broken fingers.
• Rotating drive sockets and drive extensions can
11 І 64