Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
OPERATING INSTRUCTIONS
ANALOG TONE TRACING ON INSTALLED RJ45/RJ11/RJ12 (FIG. 3) OR COAX CABLE (FIG. 4)
Use an analog tracing probe (Klein Tools VDV500-123 or VDV500-223 recommended) when performing analog
tone generation.
1. From the Home Screen, use the Arrow Buttons
press the Enter Button
.
12
2. If toning RJ45, RJ11, or RJ12 cable: Insert one end of the RJ45
appropriate port
,
or
, and the other end into the receptacle to test.
15
16
17
If testing coax cable: Insert the Female F-Barrel Connector
one end of a coax-terminated cable to the Barrel Connector, and the other end into the receptacle to test.
3. Select the appropriate settings for the cable being toned. NOTE: The Coax F-Connector Port
tone on pins 7-8 only. If toning coax cable, ensure that the tone is being generated on pins 7-8.
4. Use the probe to determine the wire(s) on which the tone is being transmitted (see tone probe instruction
manual for details). NOTE: If the cable being toned is in close proximity to other cables and tone is detected
on multiple cables, the tone will be loudest on the cable connected to the tester.
For best results wire should NOT be energized
A
B
C
D
E
FIG. 3
14
VDV501-770-1390677ART Scout Pro Max Manual.indd 15
VDV501-770-1390677ART Scout Pro Max Manual.indd 15
,
,
,
to navigate to the Analog Toning Icon
8
9
10
11
, RJ11
or RJ12
cable into the
19
20
21
into the Coax F-Connector Port
25
16
16
A.
Wire(s) being toned
B.
Cable type & VoP
C.
Toned wire selector (press "Soft
Key" Button
to change)
4
I
D.
Toning frequency (press "Soft
Key" Button
to change)
5
H
E.
Digital/Analog toning select
(press "Soft Key" Button
change)
F.
Auto Power-Off settings (press
G
"Soft Key" Button
G.
Wiring standard being tested
(changeable in SETTINGS)
H.
Auto Power-Off time
I.
Toning type and frequency
F
FIG. 4
DIGITAL TONE TRACING ON INSTALLED RJ45/RJ11/RJ12 (FIG. 5)
Digital toning requires Klein Tools VDV500-223 Probe; other probes are not compatible with this function.
1. Press the Power Button
and
E6
2. From the Home Screen, use the Arrow Buttons
press the Enter Button
3. If toning RJ45, RJ11, or RJ12 cable: Insert one end of the RJ45
appropriate port
,
15
, then connect
4. Select the appropriate settings for the cable being toned.
5. Use the probe to determine the wire(s) on which the tone is being transmitted (see tone probe instruction
transmits
manual for details). NOTE: If the cable being toned is in close proximity to other cables and tone is detected
on multiple cables, the tone will be loudest on the cable connected to the tester.
For best results wire should NOT be energized
A
to
6
to change)
7
B
C
OPERATING INSTRUCTIONS
to turn on the tester.
3
,
,
,
to navigate to the Digital Toning Icon
8
9
10
11
.
12
, RJ11
19
or
, and the other end into the receptacle to test.
16
17
H
G
F
D
E
FIG. 5
and
E7
or RJ12
cable into the
20
21
A.
Wire(s) being toned
B.
Cable type & VoP
C.
Toned wire selector (press "Soft
Key" Button
to change)
4
D.
Digital/Analog toning select
(press "Soft Key" Button
to
6
change)
E.
Auto Power-Off settings (press
"Soft Key" Button
to change)
7
F.
Wiring standard being tested
(changeable in SETTINGS)
G.
Auto Power-Off time
H.
Toning type
15
8/20/2024 6:45:14 PM
8/20/2024 6:45:14 PM
Werbung
