Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
OPERATING INSTRUCTIONS
RJ11/RJ12 WIREMAP TESTING AND LENGTH MEASUREMENT
1. Plug one end of an RJ11 or RJ12-terminated cable into the RJ11/RJ12 port
RJ11/12 port
on the Test + Map™ ID Remote
1A
2. From the Home Screen, use the Arrow Buttons
press the Enter Button
.
12
3. The tester will automatically begin testing and the LCD screen will display the results.
4. Press the Enter Button
to test again.
12
MEASURING LENGTH TO FAULTS (VOICE CABLE)
If fault is a SHORT:
5. While measuring a voice cable, if there is a short between pairs (i.e. a short between wires 1-6, 2-5, 3-4 for
RJ12 type or 1-4, 2-3 for RJ11 type), the tester will display "SHORT" and show a red line between the shorted
wires in the Wiremap section
. The tester will also indicate the approximate distance to the short location.
A
6. If there is a short between non-pair wires, the tester will indicate and display "SHORT" on all affected wire
pairs. For example, if there is short between wire #4 and wire #5 (RJ12), the tester will display "SHORT" on
both wire pairs 2-5 and 3-4 and show a red line between the shorted wires in the Wiremap section
tester will also indicate the approximate distance to the short location.
If fault is an OPEN:
1. While measuring a voice cable, if there is an open wire pair, the tester will display "OPEN" and show a red
for the affected wires in the Wiremap section
open location.
If there are MULTIPLE faults:
1. If more than one type of fault is encountered, the tester will display "MULTI" and show the appropriate fault
icons for the corresponding wires in the Wiremap section
distance to the first fault encountered.
NOTE: Cable length is determined by the Velocity of Propagation (VoP) of the cable. Ensure the correct VoP is
entered for accurate length measurements.
A
F
A.
Wiremap (will also display any faults detected)
B.
Length measurement (pairs)
C.
Test result
D.
Remote ID number
NOTE: ID number recognition is achieved through wire pair 2-5 for RJ12, and wire pair 1-4 for RJ11. If
wires 2 and 5 (RJ12) or wires 1 and 4 (RJ11) are short circuited, or one of them is open circuited, the ID
number cannot be recognized.
E.
Port Type
F.
Cable Type Indicator
G.
Cable Type Button (press "Soft Key" Button
H.
One-Time / Continuous Test Button (One-Time mode shown, press "Soft Key" Button
NOTE: in One-Time Test mode, press Enter Button
I.
Save Button (press "Soft Key" Button
)
7
8
VDV501-770-1390677ART Scout Pro Max Manual.indd 8-9
VDV501-770-1390677ART Scout Pro Max Manual.indd 8-9
, and the other end into the
17
.
1
,
,
,
to navigate to the Voice Mode Icon
8
9
10
11
. The tester will also indicate the approximate distance to the
A
. The tester will also indicate the approximate
A
B
C
D
E
G
H
I
to change)
5
to change)
6
to repeat test
12
COAX TESTING AND LENGTH MEASUREMENT
1. Insert the Female F-Barrel Connector
terminated cable to the Barrel Connector, and the other end to the Coax F-Connector Port
Map™ ID Remote
.
and
1
E2
2. From the Home Screen, use the Arrow Buttons
press the Enter Button
3. The tester will automatically begin testing and the LCD screen will display the results.
4. Press the Enter Button
MEASURING LENGTH TO FAULTS (COAX CABLE)
If fault is a SHORT:
5. While measuring a coax cable, if a short is encountered, the tester will display "SHORT" and indicate the
approximate distance to the short location.
If fault is an OPEN:
. The
A
1. While measuring coax cable, if an open is encountered, the tester will display "OPEN" and show a red X and
indicate the approximate distance to the open location.
NOTE: Cable length is determined by the Velocity of Propagation (VoP) of the cable. Ensure the correct VoP is
X
entered for accurate length measurements. See VoP section for more detail.
D
A.
Length measurement (pairs)
B.
Test result
C.
Remote ID number
D.
Cable Type Indicator
E.
Cable Type Button (press "Soft Key" Button
F.
One-Time / Continuous Test Button (Continuous Mode shown, press "Soft Key" Button
NOTE: in One-Time Test mode, press Enter Button
G.
Save Button (press "Soft Key" Button
OPERATING INSTRUCTIONS
into the Coax F-Connector Port
25
,
,
,
to navigate to the Coax Mode Icon
8
9
10
11
.
12
to test again.
12
E
F
to change)
5
to repeat test
12
)
7
, then connect one end of a coax-
16
on the Test +
1C
and
E3
A
B
C
G
to change)
6
9
8/20/2024 6:44:34 PM
8/20/2024 6:44:34 PM
Werbung
