Gastroback Design Multi Juicer Digital Pro Bedienungsanleitung Seite 59

Problem Reason The Solution
The sealing surface Replace the mixing jug. Do not use any chipped or cracked
of the mixing jug is glass parts for preparing food to avoid injuries due to splinters
chipped or broken. in your food!
The sealing ring is The sealing ring must be in proper working order. There may be no
damaged. tears, cracks, or brittle or worn out parts. Replace the sealing ring.
There are residues Clean all sealing surfaces thoroughly, removing all dried-on
of food sticking to crusts and residues of food (see: 'Cleaning the Mixing and Grin-
the sealing surfaces ding System').
of the mixing jug,
sealing ring, or bla-
de assembly.
You cannot lock the The coupling at Without pressure, turn the blade assembly over the drive cou-
blade assembly on the bottom of the pling of the motor base to and fro, until the blade assembly
the motor base. The blade assembly did slides down and comes to a stable stand without any gap. Then
mixing jug / grin- not slide onto the turn the blade assembly clockwise to lock it (see: 'Blending
ding cup is wobbling drive coupling of the Runny Food or Solid Ingredients' or 'Grinding Dry Food'').
on the motor base. motor base.
You cannot fix the Only when using the With accessories for mixing and grinding simply leave the
locking arm in the juicing system, you locking arm in the horizontal position. The appliance will reco-
upper closed position. must (and can) enga- gnize the type of system installed.
ge the locking arm.
When turning the The junction between Switch "OFF" the appliance and unplug from the power supply.
selection dial to the glass container and Remove the processing system from the motor base. Try to turn
desired speed, the blade assembly is on the blade assembly a little more tightly. Due to the sealing
display is illumina- not turned on suffici- ring, there is a firm resistance when screwing on the blade
ted, but the motor ently tight. assembly.
does not start.
The thread between Switch "OFF" the appliance and unplug from the power supply.
blade assembly and Remove the processing system from the motor base. Unscrew
glass container is the blade assembly. Then re-assemble the processing system
tilted. without tilting the threads to avoid damage and ensure correct
and leak-free operation (See: 'Assembling the Mixing Jug' or
'Assembling the Grinding System').
The processing sys- Switch "OFF" the appliance completely. Clasp the collar of the
tem is not locked to blade assembly with both hands and turn the blade assem-
the motor base suffi- bly clockwise a little more. When feeling the first resistance,
ciently tight. you must turn the blade assembly a little more than a finger's
breadth to lock the processing system onto the motor base.
116
Problem Reason The Solution
Liquids run down on The mixing jug is Immediately unplug the appliance. Then clean the appliance
the exterior of the overfilled. (see: 'Care and Cleaning'). Leave the motor base dry naturally
mixing jug and/or for 1 day. Always observe the maximum filling level for each
accumulate under glass container (see: 'Technical Specifications').
the motor base duri-
Some liquid has Immediately unplug the appliance. Then clean the appliance
ng operation.
been spilled while (see: 'Care and Cleaning'). Leave the motor base dry naturally
filling the mixing for 1 day. Whenever possible, you should remove the mixing
jug. jug from the motor base for filling. Otherwise, carefully avoid
spilling liquids onto the exterior of the appliance. Always wipe
spilled liquids off immediately.
You did not close Immediately unplug the appliance. Then clean the appliance
the mixing jug with (see: 'Care and Cleaning'). Leave the motor base dry naturally
the appropriate lid for 1 day. Always ensure to close the lid correctly, before star-
or the lid has not ting operation.
been closed proper-
ly, during operation.
Mixing system: duri- Operate the appliance at speed level 1, when adding ingredients,
ng operation, the while the motor is running (e.g. for mayonaise). Avoid filling the
ingredients cup was mixing jug up to the maximum possible amount. Ensure that your
not inserted within food will not run out and wipe off spilled liquids immediately.
the mixer lid. Always replace the ingredients cup immediately after addition.
Liquid runs out from You spilled some Immediately unplug the appliance. Then clean the appliance
under the collar of liquid, when fil- (see: 'Care and Cleaning'). Leave the motor base dry naturally
the blade assembly. ling or moving the
for 1 day.
mixing jug, or the Carefully dry the exterior of the used system, before mounting
bottom of the blade the system on the motor base.
assembly has not
been completely
dry.
The mixing jug is lea- Immediately unplug the appliance. Then clean the appliance
king. (see: 'Care and Cleaning'). Leave the motor base dry naturally
for 1 day. Before operation, always check the mixing jug for
leakage by pouring in some water.
The lid of the mixing When processing This is caused by the high power and speed of the motor. With
jug falls off the solid food, pieces of the motor agitating, always keep a hand on the lid, while pro-
mixing jug and the food may knock out cessing solid foodstuffs.
food is hurled out. the lid.
117