Problem
Reason
The Solution
The motor base gets
The power cord is still
Always unwind the power cord completely before operation to
unexpectedly hot
wound partly around
avoid overheating (see: 'Before First Use').
during operation.
the cord storage duri-
ng operation.
The motor is already
Do not let the appliance operate continuously for more than 20
running continuously
minutes. With heavy load, make a break after each 7 minutes
for a too long time.
(see: 'Method of Operation and Making Breaks'). If required,
process your food in portions.
Malfunction has
Immediately unplug the appliance. Get in contact with an autho-
occurred.
rised service centre for examination and repair.
The motor stops
Too much too hard
Immediately switch off (selection dial to "OFF", power switch
unexpectedly during
or fibrous food in
to "O") and unplug (see: 'Electronic Overload Protection').
operation.
the processing sys-
Remove the obstacle (see: 'Emptying the Containers and Remo-
tem is blocking the
ving Obstacles' or Using the Mixing Jug / Removing Obstacles
knives.
from the Mixing Jug'). Thereafter, try again.
The overheat protec-
Immediately switch off (selection dial to "OFF", power switch to "O")
tion device has been
and unplug. Leave the appliance cool down for at least 30 minutes
triggered.
(see: 'Self-Resetting Overheat Protection Device'). Thereafter, try again.
The electronic over-
Immediately switch off (selection dial to "OFF", power switch
load protection has
to "O") and unplug (see: 'Electronic Overload Protection').
been triggered.
Remove the obstacle (see: 'Emptying the Containers and Remo-
ving Obstacles' or 'Using the Mixing Jug / Removing Obstacles
from the Mixing Jug'). '). Thereafter, try again.
After leaving the
Simply turn the selection dial to another speed selection to re-
appliance operate
activate the appliance (see: 'Automatic Shut-Off'). However,
for more then 20
you should make a break of at least 20 minutes: switch "OFF"
minutes, the auto-
the appliance completely (at the selection dial and power
matic shut-off has
switch). Then unplug the appliance and wait for the appliance
been triggered.
to cool down.
112
JUICING SYSTEM
Problem
Reason
The Solution
The juice collector
The pulp container is
Place the pulp container onto the pulp container protrusion at
does not fit onto the
not placed correctly
the bottom of the motor base. If positioned correctly, it will fit
motor base.
at the side of the
closely to the side of the motor base.
motor base.
Wrong orientation of
The juice spout of the juice collector must fit into the groove
the juice collector.
at the motor base and the pulp guttering must fit into the pulp
container. Position the juice collector accordingly.
The juicing sieve or
Remove any accessories from the drive rotor. The juice collector
any other accessory
is always mounted BEFORE inserting the juicing sieve.
is still mounted on
the drive rotor.
You cannot close
The juicing sieve is
Remove the juicer cover. Turn the juicing sieve without pressure
the gap between
not engaged at the
over the drive rotor until the juicing sieve slides down easily.
juice collector and
drive rotor.
Then push down the juicing sieve slightly to make it engage
juicer cover.
tangibly on the drive rotor.
The pulp container is
Place the pulp container on the protrusion at the bottom of the
not positioned cor-
motor base. Otherwise, the pulp spout of the juicer cover cannot
rectly.
close the pulp container.
You cannot fix the
The juice collector
Ensure that the juice collector and juice cover are mounted tight-
locking arm in its
or juicer cover is not
ly and without any gaps.
upper locked position.
mounted correctly.
The juicing sieve is
Remove the juicer cover and turn the juicing sieve to and fro on
not locked to the
the drive rotor until it slides down. Then push the juicing sieve
drive rotor correctly.
down gently. It must engage tangibly on the drive rotor. The-
reafter mount the juicer cover again. There may be no gap bet-
ween juicer cover and juice collector. Try again.
Liquids run over the
The juice collector
Immediately unplug the appliance. Clean and dry the appliance
rim of the motor
or juice spout is
(see: 'Cleaning the Juicing System') and leave the motor base
base and/or are
blocked.
dry naturally for 1 day. Always ensure to turn the drip-stop at
accumulating under
the juice spout of the juice collector open before juicing (see:
the motor base.
'Drip-Stop Feature'). Check the juice collector for any obstacles
(see: 'Emptying the Containers and Removing Obstacles').
113