Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• Kinks where the connection cable has been improper-
ly fastened or routed,
• Places where the connection cables have been cut
due to being driven over,
• Insulation damage due to being ripped out of the wall
socket,
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be
used and are life-threatening due to the insulation dam-
age.
Check the electrical connection cables for damage regu-
larly. Ensure that the connection cables are disconnected
from electrical power when checking for damage.
Electrical connection cables must comply with the appli-
cable VDE and DIN provisions. Only use connection ca-
bles with the same designation "H05VV-F".
The printing of the type designation on the connection ca-
ble is mandatory.
10.2
AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a cross-
section of 1.5 mm².
Connections and repair work on the electrical equipment
may only be carried out by electricians.
Connection type Y
If it is necessary to replace the mains connection cable,
this must be done by the manufacturer or their represen-
tative to avoid safety hazards.
11 Cleaning, maintenance, storage
and transport
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always carry out
maintenance and cleaning work with the mo-
tor switched off and the mains plug discon-
nected. There is a danger of injury! Let the
Product cool down before all maintenance
and cleaning tasks. Elements of the engine
are hot. There is a danger of injury and burn-
ing!
The product can start unexpectedly and cause injuries.
–
Switch off the motor before carrying out any clean-
ing or maintenance work.
–
Allow the motor to cool down.
–
Pull out the mains plug!
–
De-pressurise the compressor!
11.1
Cleaning
• Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend that
you clean the product directly after every use.
• Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the product. Make sure that no water can pen-
etrate the product interior.
• We recommend that you clean the product directly af-
ter every use.
• The hose and injection tools must be disconnected
from the compressor before cleaning. The compressor
must not be cleaned with water, solvents or similar.
11.2
Maintenance
Check the condition of the product regularly. Check,
among other things, whether:
• the buttons are undamaged,
• the accessories are in flawless condition,
• the mains cables and the plugs are undamaged,
• the ventilation slots are free and clean. If necessary,
use a soft brush or paintbrush to clean it.
11.3
Storage and transport
ATTENTION
Pull out the mains plug and ventilate the compressor
and all connected compressed air tools. Store the com-
pressor in such a way that it cannot be used by unau-
thorised persons.
Store the product and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature is between 5°C and
30˚C.
Store the product in its original packaging.
Cover the product to protect it from dust or moisture.
Store the operating manual with the product.
• Clean and maintain the product before storage.
• Remove the battery from the product before pro-
longed storage (e.g. winter storage).
• Transport the product using the transport handle pro-
vided ().
12 Repair & ordering spare parts
With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that
the following parts are required as consumables.
ATTENTION
According to the German Product Liability Act, no liabili-
ty is accepted for damage caused by improper repairs
or by not using original spare parts.
Such work should be performed by a customer service
centre or an authorised specialists. The same applies to
accessory parts.
www.scheppach.com
GB | 23
Werbung
