Werbung
for personal protection against falls from heights. Two risks are possible: 1) Mounting upside down. Solution: put the absorber side on
the harness side. 2) Incorrect closure of the AM002 carabiner. Solution: check that the double action of closing the carabiner AM002 is
done correctly. WARNING !: AN208S200CD/AN218S200CDD (Rfu CNB/P/11.074) : 1) Premature wear of the rope (use over an edge).
Solution: Rope surrounded by a thermoformed sheath. Usage limits: Before any PPE implementation operation, set up a rescue plan
to deal with any emergency that may occur during the operation. Textile products or those containing textile elements (harnesses, belts,
shock absorbers etc...): maximum life of 10 years in storage (from date of manufacture), 7 years after the first use. The shelf life is given
as an indication. The following factors can cause it to vary greatly: -Non-compliance with the manufacturer's instructions for transport,
storage and use /-"Aggressive" work environment: marine atmosphere, chemicals, extreme temperatures, sharp edges... /-Particularly
intensive use /-Shock or significant constraint /-Disregard for the product item's history. In the case of doubt or if the device was used
to stop a fall, it must be immediately withdrawn from use and returned to the manufacturer or any competent person appointed by them.
▪Warning: these factors can cause damage invisible to the naked eye. Warning: certain extreme conditions can shorten the shelf life by
a few days. If in doubt, always remove the product for it to undergo either: - a review /- destruction. The shelf life is not a substitute for
periodic verification (minimum annually) which will assess the condition of the product. ➪ TO FIND YOUR LOCAL ANNUAL REVIEW
CENTRE, VISIT WWW.DELTAPLUS.EU. No modification or addition or repair of the PPE may be made without prior written consent
from the manufacturer nor without using their procedures. Do not use beyond the area of use defined in the instructions for use. The
manufacturer cannot be held liable for any direct or indirect accident after a modification or use other than that provided in this manual.
Do not use this equipment beyond its limits. To ensure its working condition and therefore the safety of the user, the product must be
checked systematically: ▪1 / visually inspect the following points: State of the strap or rope: no fraying, no boot cut, no visible damage
at seams, no burning and no unusual narrowing. / Condition of seams and fasteners: no visible damage . / Condition of the metal parts:
no wear, no deformation, no corrosion or oxidation. /General condition: look for any possible damage due to ultraviolet radiation and
other climatic conditions / Correct operation and locking of connectors . / Specific conditions such as humidity, snow, ice, mud, dirt, paint,
oil, glue, corrosion, wear of the strap or rope, etc..., can significantly reduce the operation of the fall arrest device. ▪2 / in the following
cases: Before and during use / if in doubt / In the case of contact with chemicals, solvents or fuels that could affect operation. / If it has
been subjected to stress during a previous fall. / At least every twelve months by the manufacturer or a competent organization, mandated
by them. ➪ PERIODIC REVIEW of PPE: An examination must be performed at least every twelve months by the manufacturer or a
competent organization, mandated by them. This very important check is related to the maintenance and efficacy of the PPE and hence
the user's safety. A written document authorising reuse should be obtained during this audit in order to reuse the PPE. This document
will clarify that the user's safety is linked to maintaining the efficiency and resistance of the equipment. Replace the PPE if necessary. In
accordance with European regulations, the identification form must be completed prior to the first use of the product and then updated
and kept with the product as well as the manual by the user. The readability of the product labelling must be checked periodically.
▪WARNINGS: The user's safety depends on the continuing efficacy of the PPE, its strength and the proper understanding of the
instructions in this manual. Any static or dynamic overload may damage the PPE. The weight of the user, including his clothing and
equipment must not exceed the maximum weight indicated on the fall arrest. It is dangerous to create your own fall arrest system as
each safety function may interfere with another safety function. No modification or addition or repair of the PPE may be made without
prior written consent from the manufacturer without using their procedures. Do not use beyond the scope of use defined in the usage
instructions, nor beyond its limits. The manufacturer cannot be held liable for any direct or indirect accident after a modification or use
other than that provided in this manual. ▪Temperature of working environment : -20°C / +50°C. ▪ PART 2: RECORD CARD :PERIODIC
REVIEW of PPE: 1/Reference of the product 2/Company 3/User Name 4/The batch number,/Serial N° 5/Production date 6/Date
of 1st Use 7/Purchase date 8/Date of inspection 9/Comments 10/Date of next inspection 11/Name & Signature 12/Type Personal
protective equipment 13/LANYARD WITH SHOCK ABSORBER (according to EN355). 14/The record card must be completed by the
user before the product is first used, then regularly updated and kept. To be exclusively used as described in the product user instructions.
15/The frequency of inspections must comply with national regulations and in any case an inspection must be performed at least once a
year. The documentation supplied with each product must be kept indefinitely by the user. Storage/Cleaning instructions: ▪ During
transport and storage: - keep the product in its packaging /-keep the product away from any sharp, abrasive, objects etc... / Keep the
product away from sunlight, heat, flames, hot metal, oil, petroleum products, harsh chemicals, acids, dyes, solvents, sharp edges and
structures of small diameter. These items can affect the performance of the fall arrest device. Store the equipment dry and clean in its
original packing, away from light, cold, heat and humidity and at ambient temperature. SERVICING AND STORAGE: Clean with soap
and water, wipe with a cloth and hang in a ventilated area to dry naturally away from any direct fire or source of heat, even for items that
got wet during use. Do not use bleach, harsh detergents, solvents, gasoline or coloring, these substances can affect the performance
of product. ▪ The metal parts are wiped with a cloth soaked in vaseline oil. Bleach and detergents are strictly prohibited. ▪ Clean the
strap with a soft detergent only. ▪ Storage after cleaning, away from light in a dry and ventilated place. IT CINGHIA CON ASSORBITORE
DI ENERGIA (secondo EN 355).- AN201200CC: ASSORBITORE DI ENERGIA CON CORDA 2 M + 2 AM002 AN208S200CD:
ASSORBITORE DI ENERGIA CON CORDA 2 M CON GUAINA+ 1 AM002 + 1 AM022 AN218S200CDD: ASSORBITORE DI ENERGIA
CON CORDA DOPPIA 2 M CON GUAINA + 1 AM002 + 2 AM022 M AN201200CD: ASSORBITORE DI ENERGIA CON CORDA 2 M +
1 AM022 + AM002 AN203100CC: ASSORBITORE DI ENERGIA A CINGHIA 1 M + 2 AM002 AN203200CC: ASSORBITORE DI
ENERGIA A CINGHIA 2 M + 2 AM002 AN203200CD: ASSORBITORE DI ENERGIA A CINGHIA 2 M + 1 AM022 + AM002 AN208150CC:
ASSORBITORE DI ENERGIA CON CORDA 1,5 M + 2 AM002 AN208RCD: ASSORBITORE DI ENERGIA CON CORDA REGOLABILE
DA 1,5 A 2 M + 1 AM022 + 1 AM002 AN211200CCC: ASSORBITORE DI ENERGIA CON CORDA DOPPIA 2 M + 3 AM002
AN211200CDD: ASSORBITORE DI ENERGIA CON CORDA DOPPIA 2 M + 2 AM022 + 1 AM002 AN213100CDD: ASSORBITORE DI
ENERGIA A CINGHIA DOPPIA 1 M + 2 AM022 + 1 AM002 AN213200CCC: ASSORBITORE DI ENERGIA A CINGHIA DOPPIA 2 M +
3 AM002 AN213200CDD: ASSORBITORE DI ENERGIA A CINGHIA DOPPIA 2 M +
ASSORBITORE DI ENERGIA CON CORDA DOPPIA 1,5 M + 3 AM002 AN218RCDD: ASSORBITORE DI ENERGIA CON CORDA
DOPPIA REGOLABILE DA 1,5 A 2 M + 2 AM022 + 1 AM002 AN230CD: ASSORBITORE DI ENERGIA ESTENSIBILE CON CINGHIA 2
M + 1 AM022 + 1 AM002 AN235200CD: ASSORBITORE DI CADUTA CON CINGHIA ESTENSIBILE 2 M + 1 AM002 + 1 AM022
AN235200PR: ASSORBITORE DI ENERGIA DIELETTRICO A CINGHIA ESTENSIBILE 2 M + 1 AM010D + 1 AM022D AN240CDD:
ASSORBITORE DI ENERGIA ESTENSIBILE CON CINGHIA DOPPIA 2 M + 2 AM022 + 1 AM002 AN245200CDD: ASSORBITORE DI
CADUTA CON CINGHIA ESTENSIBILE
DIELETTRICO A CINGHIA ESTENSIBILE DOPPIA 2 M + 1 AM010D + 2 AM022D AN218R2CDD: ASSORBITORE DI ENERGIA CON
CORDA DOPPIA REGOLABILE DA 1,5 A 2 M + 2 AM022 + 1 AM002 AN208R2CD: ASSORBITORE DI ENERGIA CON CORDA
REGOLABILE DA 1,5 A 2 M + 1 AM022 + 1 AM002 Istruzioni d'uso: La presente notifica deve essere tradotta (eventualmente) dal
rivenditore nella lingua del paese in cui l'attrezzatura viene utilizzata. La notifica deve essere letta e compresa dall'utilizzatore che dovrà
utilizzare l'EPI. I metodi di prova descritti nelle norme non rappresentano le vere condizioni di impiego. E' importante studiare a fondo
ogni situazione di lavoro ed ogni utilizzatore dovrà essere adeguatamente formato alle diverse tecniche per conoscere i limiti dei diversi
dispositivi. L'utilizzo di questo EPI è riservato a persone competenti che hanno seguito una responsabilità adeguata o che operano
controllati da un superiore competente. La sicurezza dell'utilizzatore dipende dall'efficacia costante de EPI e della corretta comprensione
delle specifiche definite nelle istruzioni d'uso. L'utilizzatore è personalmente responsabile dell'utilizzo dell'EPI non conforme con le
prescrizioni di queste istruzioni e nel caso di mancato rispetto delle istruzioni di sicurezza applicabili all'EPI precisate. L'utilizzo di questo
DPI è riservato a persona in buone condizioni di salute, visto che talune condizioni mediche potrebbero compromettere la sicurezza
dell'utilizzatore. In caso di dubbio, consultare il proprio medico. Per maggiore sicurezza, rispettare attentamente le istruzioni di utilizzo,
DELTA PLUS GROUP - ZAC La Peyrolière - BP140 - 84405 APT Cedex - France –
4
Tel: +33 (0) 4 90 74 20 33 - Fax: +33 (0) 4 90 74 32 59 - www.deltaplus.eu
DOPPIA 2 M + 1 AM002 + 2 AM022 AN245200PRR: ASSORBITORE DI ENERGIA
2 AM022 + 1 AM002 AN218150CCC:
UPDATE 05/11/2019
Werbung
