Before Commissioning; Assembly; Operation - Scheppach 5906822901 Original Bedienungsanleitung

• Try to keep the stress as low as possible. For exam-
ple: Limit working time. In doing so, all parts of the
operating cycle must be taken into account (such
as times in which the electric tool is switched off or
times in which it is switched on, but is not running
under a load).

8. Before commissioning

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, keep the packaging until the expiry of
the warranty period.
ATTENTION
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
Before connecting the machine, make certain that the
data on the type plate matches with the mains power
data.
• Check the device for transport damage. Immedi-
ately report any damage to the transport company
that delivered the electrical tool.
• Long supply cables (extension cable) should be
avoided.
• Do not operate the electrical tool in damp or wet
areas.
• Operate the electrical tool only in suitable areas
(well ventilated).

9. Assembly

m Attention!
Always make sure the device is fully assembled be-
fore commissioning!
m Before connecting the machine to the mains
power, make certain that the data on the type plate
matches with the mains power data.
m Warning! Always pull out the mains plug before
carrying out adjustments on the device.
9.1 Assembling the base plate and column (fig. 2)
1. Slide the quick clamp (2) over the column (3).
2. Set the column (3) into the base plate (1) such that
the guide pins on the bottom end of the column
(3) engage with the groove in the mount on the
base plate (1).
24 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
3. Tighten the pre-assembled fastening screws (A)
on the rear of the base plate (1) with the Allen key
(L).
9.2 Fitting the parallel stop (fig. 3)
1. Slide the parallel stop (16) into the grooves in the
base plate (1).
2. Ensure that the sliding blocks underneath the
wing screws of the parallel stop (15) are properly
engaged in the grooves of the base plate.
3. Move the parallel stop (16) to the desired position
and tighten the wing screws of the parallel stop
(15) firmly.
9.3 Assembling the chuck guard (fig. 2)
1. Insert the chuck guard (13) into the holes provided
in the machine frame.
2. Secure the chuck guard (13) by hand-tightening
the screws (C).
9.4 Assembling the handle (fig. 2)
1. Remove the pre-mounted fastening screw (B).
2. Slide the spacer sleeve (K) and the handle (8)
onto the mount (D), as shown in Fig. 2.
3. Tighten the blade fastening screw (B) firmly.
9.5 Assembling the clamping lever for depth stop
(fig. 2)
Assemble the clamping lever for depth stop (6) as
shown in fig. 2.
9.6 Fastening to a work surface (fig. 3)
Fasten the device to the work surface by bolting the
base plate (1) to the work surface.

10. Operation

10.1 Height adjustment (fig. 1)
The position of the machine head can be adjusted
to suit the workpiece height or the workpiece length.
1. Hold the handle (8) firmly.
2. Release the clamping lever for the height adjust-
ment (5).
3. Set the position of the machine head with the han-
dle (8).
4. Secure the position of the machine head with the
height adjustment clamping lever (5).
Attention! Ensure in the lowest machine head posi-
tion that the machine head will not be moved beyond
the marking.
Use the clamping lever for height adjustment (5) to
secure the machine head in this position. Otherwise,
the guide could be damaged.