Approved Fuels - CMi C-BFS-25 B-1 Originalbetriebsanleitung

All manuals and user guides at all-guides.com
Motorsense_401118_401119.book Seite 49 Donnerstag, 7. April 2016 2:28 14
Item number
Acoustic pressure (L )*
PA
• Brushcutter
• Trimmer
Noise output level (L )*
WA
• Brushcutter
• Trimmer
Vibration**
• Brushcutter
• Trimmer
Weight
Spark plug
*) The specified values are emission values and do not necessar-
ily represent safe workplace values. Although there is a corre-
lation between emission and immission levels, this cannot be
used to infer whether additional safety measures are necessary
or not. Factors which affect the current immission levels at the
workplace, include the type of room, other sources of noise,
e. g. the number of machines operating and other processes
taking place in the vicinity. Permitted workplace values can dif-
fer from country to country. This information is designed to help
the user to better assess the dangers and risks.
**) The specified vibration emission value was measured in
accordance with a normed test procedure and can be used in
order to compare one tool with another. The specified vibration
emission value can also be used for an introductory evaluation
of the exposure. The vibration emission value may fluctuate
from the specified value during actual use of the power tool.
These fluctuations will depend on the way in which the power
tool is used. Try to keep vibrations to a minimum. One method
of reducing the vibration load is, for example, limiting the length
of time you work with the tool. All parts of the operating cycle
must be taken into account for this purpose (for example, also
including times in which the power tool is switched off and
times in which it is switched on, but is running without load).

Approved fuels

NOTICE! Risk of damage to the
machine! Use only the specified fuel.
Never use oil intended for car or outboard
engines.
Note: When used in a mixture, fuel will age
particularly quickly: therefore, do not mix
more fuel than you will consume within
1 month.
• Normal petrol, 91 octane (40 parts) If no regular
petrol is available, you can also use petrol with a
higher octane ratio.
• Two-stroke motor oil for air-cooled motors, high
quality
Mixing ratio 40:1, i. e.
Regular petrol mixed with two-stroke motor oil
1 litre 25 ml
2 litres 50 ml
3 litres 75 ml
4 litres 100 ml
5 litres 125 ml
Instructions for fuels
401 118, 401 119
Fuels with ethanol mixtures (e. g. E10)
Fuels with high ethanol mixture are more aggressive
93 dB(A)
than fuels with less or without ethanol mixture. Pos-
95 dB(A)
sibly painted surfaces and plastics can be strongly
(K = 3 dB(A))
affected or damaged. Moreover, fuel with ethanol
mixture strongly reacts to influential factors such as
light rays, temperature and storage time. Hence,
107 dB(A)
these fuels should be stored only in allowed contain-
109 dB(A)
ers and in suitable place for not more than 30 days.
(K = 3 dB(A))
It is recommendable to empty the fuel tank as well as
the steam separator (carburettor) if combustion
engine takes longer time to shutdown.
< 8,72 m/s²
All our devices are suitable for using the E10 fuel.
< 7,682 m/s²
Fuels with ethanol mixtures (e. g. E10) for 2-
(K = 1,5 m/s²)
Stroke-Motor
6,9 kg
2-Stroke-Motors (Motors with petrol lubrication)
L8RTC
must be adjusted to the usage of fuel with high eth-
anol mixture (more than 5%, e.g. E10) by specialist
workshop. Thus, the country-specific environmental
conditions are to be considered and observed.
Special fuels for 2-stroke-motors
Pay attention to the details about required mixing
ratio in these instructions for use. Some completely
mixed fuels or special fuels (e. g. Aspen 2t or Stihl
Motomix) are provided only in mixing ratio of 1:50.
Spare parts
Spare parts are available from your local vendor.
Item number
310 401
310 127
396 729
GB
Spare part
Knife
Filament
Filament spool (incl. fila-
ment)
49