Black & Decker GKC1825 Originalanweisungen Seite 14

ENGLISH
Start a fresh cut.
u
Felling (fig. P, Q & R)
Inexperienced users should not attempt to fell trees. The user
may suffer injury or cause damage to property as a result of
failure to control the direction of fall, the tree may splinter or
damaged/dead branches may fall during cutting:
The safe distance between a tree to be felled and bystanders,
buildings and other objects is at least 2 1/2 times the height of
the tree. Any bystander, building or object within this distance
is at risk from being struck by the tree when felled.
Before attempting to fell a tree:
Make sure that there are no local by-laws or regulations
u
that would prohibit or control the felling of the tree.
Consider all conditions that may affect the direction of fall,
u
including:
The intended direction of fall.
u
The natural lean of the tree:
u
Any unusual heavy limb structure or decay.
u
Surrounding trees and obstacles including overhead
u
lines and underground drains.
The wind speed and direction.
u
Pre-plan a safe exit from falling trees or branches. Make sure
that the exit route is clear of obstacles that would prevent or
hinder movement. Remember that wet grass and freshly cut
bark is slippery.
Do not attempt to fell trees where the tree diameter is
u
greater than the cutting length of the chainsaw:
Cut a direction notch to determine the direction of fall.
u
Make a horizontal cut to a depth of between 1/5th and
u
1/3rd of the diameter of the tree, perpendicular to the line
of fall at the base of the tree (fig. P).
Make a second cut from above to intersect with the first
u
and make a notch of about 45°.
Make a single horizontal felling cut from the other side 25
u
mm to 50 mm above the centre of the direction notch. (fig.
Q). Do not cut through to the direction notch, you could
lose control of the direction of fall.
Drive a wedge or wedges into the felling cut to open it and
u
drop the tree (fig. R).
Pruning trees
Make sure that there are no local by-laws or regulations that
would prohibit or control the pruning of the tree limbs. Pruning
should only be undertaken by experienced users there is an
increased risk of the saw chain pinching and kick back.
Before pruning consideration should be given to
conditions affecting the direction of fall including:
The length and weight of the branch to be cut.
u
Any unusual heavy limb structure or decay.
u
Surrounding trees and obstacles including overhead.
u
14
(Original instructions)
The wind speed and direction:
u
The branch being intertwined with other branches.
u
The operator should consider access to the tree limb and the
direction of fall. The tree branch is liable to swing towards
the tree trunk. In addition to the user bystanders, objects and
property below the branch will be at risk.
To avoid splintering, make the first cut in an upward
u
direction to a maximum depth of one third the diameter of
the branch.
Make the second cut downwards to meet the first.
u
Logging (fig. S, T & U)
How you should cut depends on how the log is supported.
Use a saw horse whenever possible.
Always start a cut with the saw chain running and the spiked
bumper (20) in contact with the wood (fig. S). To complete
the cut use a pivoting action of the spiked bumper against the
wood.
When supported along its whole length:
Make a downward cut, but avoid cutting the earth as this
u
will blunt your saw chain quickly.
When supported at both ends:
First, cut one third down to avoid splintering and second,
u
cut up to meet the first cut.
When supported at one end:
First cut one third up to avoid splintering and second, cut
u
down to prevent splintering.
When on a slope:
Always stand on the uphill side.
u
When attempting to cut a log on the ground (fig. T):
Secure the workpiece using chocks or wedges. The user
u
or a bystander should not steady the log by sitting or
standing on it. Make sure that the saw chain does not
contact the ground.
When using a saw horse (fig. U):
This is strongly recommended whenever possible.
Position the log in a stable position. Always cut on the
u
outside of the saw horse arms. Use clamps or straps to
secure the workpiece.
Limbing (fig. V)
Removing the branches from a fallen tree. When limbing,
leave larger lower limbs to support the log off the ground.
Remove the small limbs in one cut. Branches under tension
should be cut from the bottom of the branch towards the top to
avoid binding the chain saw.