Cleaning The Tool - Makita UR014G Betriebsanleitung

CAUTION:
Al w ays use the shoulder harness
attached to the tool. Before operation, adjust the
shoulder harness according to the user si z e to
prevent fatigue.
CAUTION:
Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the tool.
CAUTION:
W hen you use the tool in combi-
nation of the backpack-type po w er supply such
as portable po w er pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
I f y o u p u t o n t h e s h o u l d e r h a r n e s s i n c l u d e d i n t h e
t o o l p a c k a g e a n d t h e s h o u l d e r h a r n e s s o f t h e b a c k -
p a c k - t y p e p o w e r s u p p l y a t t h e s a m e t i m e , r e m o v i n g
the tool or backpack-type power supply is difficult in
c a s e o f a n e m e r g e n c y , a n d i t m a y c a u s e a n a c c i d e n t
or injury. For the recommended hanging band, ask
M a k i t a A u t h o r i z e d S e r v i c e C e n t e r s .
1. C l a s p t h e h o o k o n t h e s h o u l d e r h a r n e s s t o t o o l ' s
r i n g a n d h a n g e r .
Fig.18: 1. R i n g 2. H o o k 3. H a n g e r
2.
P u t o n t h e s h o u l d e r h a r n e s s o n y o u r l e f t s h o u l d e r .
Adjust the shoulder harness to a comfortable working
p o s i t i o n .
Fig.19
T h e s h o u l d e r h a r n e s s f e a t u r e s a m e a n s o f q u i c k
r e l e a s e . S i m p l y s q u e e z e t h e s i d e s o f t h e b u c k l e w h i l e
h o l d i n g t h e t o o l t o r e l e a s e t h e t o o l f r o m
h a r n e s s .
Fig.20: 1. B u c k l e
Correct handling of the tool
WARNING:
Al w ays position the tool on your
right-hand side. C o r r e c t p o s i t i o n i n g o f t h e t o o l a l l o w s
f o r m a x i m u m c o n t r o l a n d w i l l r e d u c e t h e r i s k o f s e r i -
ous personal injury.
WARNING:
Be extremely careful to maintain
control of the tool at all times. Do not allo w the
tool to be de ected toward you or anyone in the
w ork vicinity. F a i l u r e t o k e e p c o n t r o l o f t h e t o o l
could result in serious injury to the bystander and the
o p e r a t o r .
WARNING:
To avoid accident, leave more
than 15m (50 ft) distance bet w een operators w hen
t w o or more operators w ork in one area. Also,
arrange a person to observe the distance bet w een
operators. If someone or an animal enters the
w orking area, immediately stop the operation.
CAUTION:
If the cutting tool accidentally
impacts a rock or hard object during operation,
stop the tool and inspect for any damage. If the
cutting tool is damaged, replace it immediately.
U s e o f a d a m a g e d c u t t i n g t o o l m a y r e s u l t i n s e r i o u s
personal injury.
C o r r e c t p o s i t i o n i n g a n d h a n d l i n g a l l o w o p t i m u m
and reduce the risk of injury.
Fig.21
W hen using a nylon cutting head (bump & feed
type)
T h e n y l o n c u t t i n g h e a d i s a d u a l s t r i n g t r i m m e r h e a d
p r o v i d e d w i t h a b u m p & f e e d m e c h a n i s m .
T o f e e d o u t t h e n y l o n c o r d , t a p t h e c u t t i n g h e a d a g a i n s t
t h e g r o u n d w h i l e r o t a t i n g .
NOTICE:
erly if the nylon cutting head is not rotating.
NOTE: I f t h e n y l o n c o r d d o e s n o t f e e d o u t w h i l e
t a p p i n g t h e h e a d , r e w i n d / r e p l a c e t h e n y l o n c o r d
b y f o l l o w i n g t h e p r o c e d u r e s i n t h e s e c t i o n f o r t h e
m a i n t e n a n c e .
MAINTENANCE
switched off and battery cartridge is removed
before attempting to perform inspection or main-
tenance on the tool. Failure to switch off and remove
t h e b a t t e r y c a r t r i d g e m a y r e s u l t i n s e r i o u s p e r s o n a l
injury from accidental start-up.
NOTICE:
alcohol or the like. Discoloration, deformation or
cracks may result.
T o m a i n t a i n p r o d u c t S A F E T Y a n d R E L IA B I L I T Y ,
t h e s h o u l d e r
repairs, any other maintenance or adjustment should
b e p e r f o r m e d b y M a k i t a A u t h o r i z e d o r F a c t o r y S e r v i c e
C e n t e r s , a l w a y s u s i n g M a k i t a r e p l a c e m e n t p a r t s .

Cleaning the tool

Clean the tool by wiping off dust, dirt, or cut off grass
w i t h a d r y c l o t h o r o n e d i p p e d i n s o a p y w a t e r a n d w r u n g
o u t . T o a v o i d o v e r h e a t i n g o f t h e t o o l , b e s u r e t o r e m o v e
the cut off grass or debris adhered to the vent of the
t o o l .
Replacing the nylon cord
diameter specified in this instruction manual.
Never use heavier line, metal w ire, rope or the
like. F a i l u r e t o d o s o m a y c a u s e d a m a g e t o t h e t o o l
and result in serious personal injury.
head from the tool w hen replacing the nylon cord.
nylon cutting head is secured to the housing
properly as described belo w . F a i l u r e t o p r o p e r l y
s e c u r e t h e c o v e r m a y c a u s e t h e n y l o n c u t t i n g h e a d t o
fly apart resulting in serious personal injury.
R e p l a c e t h e n y l o n c o r d i f i t i s n o t f e d a n y m o r e . T h e
m e t h o d o f r e p l a c i n g t h e n y l o n c o r d v a r i e s d e p e n d i n g o n
t h e t y p e o f t h e n y l o n c u t t i n g h e a d .
c o n t r o l
121-SP
17 ENGLISH
Fig.22: 1. Most effective cutting area
The bump feed w ill not operate prop-
WARNING:
Al w ays be sure that the tool is
Never use gasoline, ben z ine, thinner,
WARNING:
Use only the nylon cord w ith
WARNING:
Al w ays remove the nylon cutting
WARNING:
Make sure that the cover of the
Fig.23