Cleaning, Maintenance And Ordering Spare Parts; Disposal And Recycling - EINHELL GE-WS 18/10 Li-Solo Originalbetriebsanleitung

7. Cleaning, maintenance and
ordering spare parts
Hazard!
Always pull out the battery pack before starting
any cleaning work. Never use fl ammable solvents
to clean the equipment.
7.1 Cleaning (outside)
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Cleaning the inside of the container.
After use, clean the equipment and leave the con-
tainer open to dry. Note the cleaning instructions
in the directions for use that came with the chemi-
cal in addition to these cleaning instructions.
Remove any remaining liquid from the tank
through the container's fi ller opening and store
the liquid properly for subsequent use or dispose
of it in accordance with the applicable regulations.
1. Flip the container caps (Fig. 6/Item 5) up and
remove the motor part from the container.
2. Empty the container completely.
3. Pour about 0,5 liters of clear water into the
empty container.
4. Fit the motor part back onto the container and
close the container by hooking the caps on
the motor part and fl ipping them down.
5. Shake the pressure spray vigorously several
times.
6. Spray the contents onto the area just treated
or an area reserved for this purpose.
7. Repeat this process.
8. The container can now be drained through
the fi ller opening as described above.
9. Allow the container to dry out completely be-
fore attaching it to the motor part again.
Anl_GE_WS_18_10_Li_SPK13.indb 21 Anl_GE_WS_18_10_Li_SPK13.indb 21
GB
7.3 Cleaning the nozzle and adjustable spray
head
If foreign bodies have collected in the nozzle and
clogged it up, clean the nozzle as follows (never
blow it out with your mouth!):
1. Turn the adjustable spray head counterclock-
wise as far as it will go (Fig. 8).
2. Clean the exposed nozzle (Fig. 9a) and the
hole in the spray head (Fig. 9b) of residue
using a thin wire.
3. Flush the nozzle and spray head with clear
water.
4. Allow the nozzle and spray head to dry.
7.4 Cleaning the intake fi lter (Fig. 10)
Clean the intake fi lter in the tank at least once
a year, as soon as you notice a reduction in the
sprayed quantity of solution, or when problems
arise (see section 10).
1. Remove the motor component from the tank
(see section 5.4).
2. Clean the intake fi lter (Item E) with a brush in
clear water.
3. Place the motor component back on the tank
(see section 5.4)
7.5 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.6 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 21 -
31.01.2023 11:47:41 31.01.2023 11:47:41