Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-SY 18/60 Li-Solo Originalbetriebsanleitung

6.6 Disconnecting and cleaning the gun
(Fig. 1-2, 11-15)
Danger!
Always pull out the battery pack before starting
any cleaning work.
1. Press the trigger (5), so that the residual ma-
terial fl ows back into the container (12).
2. Unscrew the container (12) and empty the
residual material back into the material tin.
3. Clean the container (12) and the material
tube (11) with a bristle brush.
4. Pour solvent or water into the container.
Screw the container back on. Solvents with a
fl ash point above 55°C are not allowed to be
used.
5. Reinsert the battery and turn on the paint
spray gun. Set the max. paint volume control
(6) to the maximum fl ow setting. Spray the
solvent or water into a container or rag, but
never into the surroundings.
6. Repeat the procedure above until the clear
solvent or water exits from the nozzle (3).
7. Then switch off the paint spray gun and remo-
ve the battery.
8. Completely empty the container (12). Always
keep the container (12) free of residue and
check it for damage.
9. Use a rag soaked in solvent or water to clean
the outside of the paint spray gun and the
container (12).
10. Unscrew the air cap retaining ring (1) and
then remove the air cap (2). Remove the
nozzle (3). Push the fl uid needle adapter (B)
onto the fl uid needle (13). Twist and pull to
remove the fl uid needle. Clean the air cap
retaining ring, the air cap, the nozzle and the
fl uid needle with a bristle brush and solvent or
water.
11. Remove the fi lter cap (16) to clean the air inlet
fi lter. Remove the fi lter and clean it by blowing
out with air. Then reinsert the fi lter and screw
the fi lter cap onto the gun. Do not operate the
gun without the fi lter.
12. Reinsert the fl uid needle. Pull the trigger and
insert the nozzle on the fl uid needle. While
inserting, ensure that the pins on the sides of
the fl uid needle point up/down and not right/
left. Pull the trigger while placing the air cap
on the nozzle and fastening the air cap with
the air cap retaining ring.
13. Ensure that the paint spray gun is completely
dry before storing it.
14. Properly dispose of residual paint and
cleaning agents in accordance with local laws
Anl_TC_SY_18_60_Li_SPK13.indb 22 Anl_TC_SY_18_60_Li_SPK13.indb 22
GB
and regulations. Residual paint and solvents
must be taken to a suitable collection point. If
you are not sure, ask the local council where
the nearest collection point is.
Warning!
Never immerse the paint spray gun in water or
other liquids. Clean the housing only with a dam-
pened rag.
Note: If you use 2-component paint, you must
clean the gun immediately. Otherwise the paint
might dry inside the gun, causing an equipment
fault.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
- 22 -
14.01.2021 13:35:45 14.01.2021 13:35:45