Switching Off - EINHELL GE-WS 18/10 Li-Solo Originalbetriebsanleitung

To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.3 Battery charge level indicator (Fig. 5)
Press the button for the battery charge level indi-
cator (Item A). The battery charge level indicator
(Item B) shows the charge status of the battery
using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
5.4 Preparing the spray solution and fi lling
the tank
Switch off the tool and remove the battery pack.
Note:
•
Always prepare and use the spray solution in
accordance with the instructions issued by
the solution manufacturer. Fill the tank only
with the amount of solution you intend to use.
•
The consistency of the spray solution must be
similar to that of water.
•
The spray solution tank has a maximum ca-
pacity of 1.0 liter of solution.
•
Never use pesticides in living quarters, sta-
bles, or storage rooms for food and animal
feed. Pesticides are allowed to be used only
outdoors.
•
Spray solution can be prepared and tho-
roughly mixed in a separate container before
it is filled into the tank of the pressure sprayer.
Anl_GE_WS_18_10_Li_SPK13.indb 20 Anl_GE_WS_18_10_Li_SPK13.indb 20
GB
•
If you intend to use organic spray solutions,
they must be filtered before you fill them into
the sprayer.
•
Clean the tool immediately after each use.
This is the only way to keep the solution-
carrying components clean and prevent
clogging. Clogged components can result in
defects.
1. Place the pressure sprayer on a level surface.
Flip up the tank fasteners (Fig. 6/Item 5) and
lift the motor component off the spray solution
tank. The spray solution tank has a maximum
capacity of 1 liter.
2. Fill the fully prepared spray solution into the
spray solution tank. Do this with the help of a
suitable funnel if necessary. Place the motor
component back on the spray solution contai-
ner.
3. Attach the name of the current spray solution
to the spray solution tank.
6. Operation
6.1 Switching on
Press the On/Off switch (Fig. 1/Item 2).
6.2 Switching off
Let go of the On/Off switch (Fig. 1/Item 2).
6.3 Spraying
WARNING!
Read the enclosed booklet containing the safety
information.
•
Spray the plants or other objects directly with
a moderately wide spray jet.
6.3.1 Adjusting the spray jet
At the nozzle you can adjust the shape of the
spray jet from dot-shaped (concentrated spray on
a small area) to fan-shaped (fi nely atomized spray
over a large area).
1. Interrupt the spraying.
2. Turn the adjustable spray head (Fig. 7/Item 1)
counter-clockwise to obtain a narrow to dot-
shaped spray jet.
3. Turn the adjustable spray head clockwise to
obtain a wider spray jet.
6.4 Transport
Carry the tool by its handle (Fig. 1 / Item 3a).
- 20 -
31.01.2023 11:47:40 31.01.2023 11:47:40