Technical Data; Before Commissioning - Parkside PBBPS 700 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
Residual risks can be minimised if the "Safety instructions"
and "Proper use" are observed along with the whole of the
operating instructions.
8.

Technical data

Machine without blade
Length x width x height .........................270 x 230 x 240 mm
Weight unfuelled, without cutting gear approx. ..........3.4 kg
Weight unfuelled, with cutting gear approx. ............... 3.8 kg
Tank for chain lubricating oil ........................................... 0.16 l
Fuel tank content...............................................................0.23 l
Oil and fuel mixture ...........................................................1:40
Cutting length .................................................................. 20 cm
Blade length ..................................................................... 30 cm
Automatic chain oiling ......................................................... Yes
Chain pitch .................................................... 3/8" (9.525 mm)
Chain link thickness .....................................................1.27 mm
Chain type...................................................................3/8LP-40
Number of drive sprocket teeth ..............................................6
Tooth pitch of drive sprocket .............................................3/8"
Blade type .........................................................AP10-40-509P
Chain speed max. .......................................................... 21 m/s
Motor ........................................1 cylinder, 2 stroke air-cooled
Cubic capacity ...........................................................25.4 cm³
Max. engine power output per ISO 7293 ................. 0.7 kW
Idle speed n ................................................. 3300 ± 300 rpm
0
Maximum speed with cutting gear ........................11000 rpm
Spark plug ........................................................................ L8RTC
The noise pressure level should be reduced as far
as possible depending on use and the activities
to be completed so that the health of the opera-
tor is not endangered. The noise pressure level at
the workplace can exceed 80 dB (A). In this case,
noise protection measures are required for the
operator (e.g. wearing hearing protection).
Keep the noise level and vibration to a minimum!
• Only use devices which are free of defects.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.
• Wear gloves.
Measured sound pressure level L
Uncertainty K .....................................................................3 dB
pA
Guaranteed sound power level L
Measured sound power level L
Uncertainty K ....................................................................3 dB
WA
Vibration, front handle ................................................8.98 m/s²
Vibration, rear handle ................................................ 8.03 m/s²
Uncertainty.....................................................................1.5 m/s²
Wear hearing protection.
Excessive noise can result in a loss of hearing.
The specified device emissions values have been measured in
accordance with a standardised test procedure and can be
used for the comparison of one device with another.
The specified noise emission values can also be used for an
initial estimation of the exposure.
Warning:
• The noise emission values can vary from the specified val-
ues during the actual use of the device, depending on the
type and the manner in which the device is used, and in
particular the type of workpiece being processed.
• Try to keep the stress as low as possible. For example:
Limit working time. In doing so, all parts of the operating
cycle must be taken into account (such as times in which
the device is switched off or times in which it is switched
on, but is not running under a load).
9.

Before commissioning

1. Open the packaging and carefully remove the device.
2. Remove the packaging material, as well as the packag-
ing and transport safety devices (if present).
3. Check whether the scope of delivery is complete.
4. Check the device and accessory parts for transport
damage.
5. If possible, keep the packaging until the expiry of the
warranty period.
6. Remove the quick start guide from the start pull cord (8).
ATTENTION
The device and the packaging are not children's toys! Do not
let children play with plastic bags, films or small parts! There
is a danger of choking or suffocating!
..............................99.2 dB
pA
...............................113 dB
WA
.............................. 108.7 dB
WA
GB 109