Mixing Fuel - Parkside PBBPS 700 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

9.1 Mounting the guide rail (2) and tensioning
the saw chain (1)
m WARNING
Risk of injury!
Always wear protective gloves when touching the saw chain
(1). Danger of injury due to the sharp cutting teeth!
Only use approved combinations of saw chain (1) and guide
rail (2) (see chapter "Approved cutting gear").
Always carry out assembly with the engine switched off.
Note
A new saw chain (1) stretches and needs to be re-tensioned
more often. Check and adjust the chain tension regularly.
Depending on wear, the guide rail (2) can be turned.
1. Set the chainsaw down on a level and stable surface.
2. Pull the front hand guard (3) back up to the stop to re-
lease the chain brake. (Fig. 2)
3. Remove the two fixing nuts (16) with the spark plug
wrench (20).
4. Remove the chain cover (17).
5. Turn the chain tensioning screw (23) (anti-clockwise) un-
til the chain tensioning pin (26) is at the right-hand stop
(Fig. 3). Use the slotted screwdriver (20) for this.
6. Slide the slotted hole of the guide rail (2) over the two
protruding fastening pins (29).
7. Place the saw chain (1) over the teeth of the chain wheel
(27). Insert the saw chain (1) accurately into the guide
rail (2). In the tip of the guide rail (2) there is a sprocket
(30) into whose teeth the saw chain (1) must be inserted.
(Fig. 6 and 18)
8. Pull slightly on the guide rail (2) to slightly pre-tension
the saw chain (1).
9. Fit the chain cover (17) back on. Make sure that the
internal chain tensioning pin (26) fits into the matching
hole in the guide rail (2). If necessary, adjust the chain
tensioning screw (23) with the slotted screwdriver (20).
10. Screw on the two fastening nuts (16) by hand. However,
make sure that you do not tighten them yet. The fasten-
ing nuts (16) are tightened only after tensioning the saw
chain (1).
110 GB
9.2 Tensioning and checking the saw chain (1)
m WARNING
Put on protective gloves! Danger of injury due to the sharp
cutting teeth!
Check the chain tension regularly before each start-up.
Always carry out checks before starting up and with the engine
switched off.
1. Before tensioning, loosen the two fixing nuts (16) a little
with the spark plug wrench (20).
2. Turn the chain tensioning screw (23) clockwise with the
slotted screwdriver (20) to increase the tension.
3. Tighten the two fixing nuts (16) with the spark plug
wrench (20).
4. The saw chain (1) must be in contact with the underside
of the guide rail. Check whether the saw chain (1) can
be pulled over the guide rail (2) by hand (with the chain
brake released, pull the front hand guard (3) back).
NOTE
A new saw chain (1) stretches and needs to be re-tensioned
more often.
9.3

Mixing fuel

The engine must be operated with a fuel mixture of petrol
and engine oil.
m WARNING
Avoid direct skin contact with fuel and inhalation of fuel va-
pours.
Use only a mixture of unleaded petrol (min. RON 95) and
special 2-stroke engine oil (JASO FD/ISO - L - EGD). Mix the
fuel mixture as per the fuel mixing table.
Put the correct amount of petrol and 2-stroke oil into the
enclosed mixing bottle (22) (see "Fuel mixing table"). Then
shake the mixing container (22) well.
9.3.1 Fuel mixing table
Mixing process: 40 parts petrol to 1 part oil
Petrol ................................................ 2-stroke oil
0.5 litres...................................................12.5 ml