Before Use; Mixing Fuel; Adding Chain Oil; Tightening And Checking The Saw Chain - Scheppach 5910114903 Originalbetriebsanleitung

8. Before use

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swallow-
ing and suffocation!
• Remove the quick start guide from the start pull
cord (4).

8.1 Mixing fuel

The engine must be operated with a mixture of petrol
and motor oil.
m WARNING
Avoid direct skin contact with fuel and inhaling fuel
vapours.
Always use a mixture of unleaded petrol (at least
RON 95) and special 2-stroke engine oil (JASO FD/
ISO-L-EGD). Mix up the fuel mix according to the fuel
mixing table.
Pour the correct amount of petrol and 2-stroke oil into
the supplied mixing container (30) (see "Fuel mix ta-
ble"). Then shake the mixing container (30) gut durch.
8.1.1 Fuel mix table
Mixing process: 40 parts petrol to 1 part oil
Petrol
0.5 litres
8.2 Adding fuel
m WARNING
Fill the fuel tank only when the engine is switched off
and cooled down. There is a risk of fire!
• Always clean the area around the fuel tank cap (13)
before filling to prevent dirt getting into the tank.
Use a dry, lint-free cloth to do this.
• Lay the appliance on its side so that the fuel tank
cap (13) is facing upwards.
• Turn the fuel tank cap (13) anticlockwise and re-
move it. The fuel tank cap (13) is connected to the
fuel tank with an anti-loss device and cannot fall
down.
34 | GB
• Fill the tank with the fuel mix. Do not spill any fuel
• Wipe up any spilled fuel immediately.
• Turn the fuel tank cap (13) clockwise to close it.
NOTE
When filling the fuel tank, also check the chain oil.

8.3 Adding chain oil

m WARNING
Fill the chain oil only when the engine is switched off
and cooled down. There is a risk of fire!
Never work without chain lubrication! If the saw chain
runs dry, the cutting equipment may become irrepa-
rably damaged in a short time.
Always check chain lubrication before starting work.
NOTE
Use only saw chain oil. Preferably biodegradable. Do
not use waste oil, motor oil, etc.
While working, check whether the chain lubrication is
working correctly.
• Always clean the area around the chain oil tank
• Lay the appliance on its side so that the chain oil
• Turn the chain oil tank cap (14) anticlockwise and
• Add the supplied organic chain oil to the chain oil
• Wipe up any spilt chain oil immediately.
• Turn the chain oil tank cap (14) clockwise to close it.

8.4 Tightening and checking the saw chain

2-stroke oil
m WARNING
12.5 ml
Wear protective gloves! There is a danger of injury
from the sharp cutting teeth!
Check the chain tensioning before every use.
• Before tensioning, slightly loosen both locking nuts
• Turn the chain-tensioner screw (21) in a clockwise
• Tighten the two locking nuts (20) firmly using the
• The saw chain (17) must lie against the underside of
www.scheppach.com
while filling the tank and do not fill the tank to over-
flowing.
cap (14) before filling to prevent dirt getting into the
chain oil tank. Use a dry, lint-free cloth to do this.
tank cap (14) is facing upwards.
remove it. The chain oil tank cap (14) is connected
to the chain oil tank with an anti-loss device and
cannot fall down.
tank. Do not spill any chain oil while filling the chain
oil tank and do not fill the tank to overflowing.
(20) using the spark plug spanner (31).
direction using the flat-blade screwdriver (31) to in-
crease the tension.
spark plug spanner (31).
the blade. Check whether the saw chain (17) (chain
brake off, pull front hand guard (1) to the rear) can
be drawn over the guide rail (16) by hand.