Technical Data; Before Starting Up - Scheppach CSH46 Original Bedienungsanleitung

Behaviour during an emergency
Start First Aid measures relevant to the injury and re-
quest medical help as quickly as possible. Prevent
the injured person from further injury and keep him/
her rested. For potentially occurring accidents, the
First Aid kit, according to DIN 13164, should always
be handy at the work place. Material taken from the
First Aid kit must be replaced immediately. When you
are requesting help, give the following information:
1. Location of accident
2. Type of accident
3. Number of injured people
4. Type of injuries
Store all safety notices and instructions for the
future.

6. Technical data

Machine without guide bar
L x W x H
Weight without guide bar
and saw chain and empty
tank
Weight with guide bar and
saw chain and empty tank
Cutting Length
Guide bar length
Automatic chain oiling
Saw chain Oil
Saw chain oil tank capac-
ity
Saw chain division
Drive link thickness
Saw chain type
Number of teeths drive
sprocket
Tooth pitch of drive
sprocket
Chain brake
Guide bar type
Saw chain speed max.
Motor
Engine capacity
Maximum motor capacity
Idle speed
Maximum speed with cut-
ting attachment
Fuel tank capacity
Fuel type
46 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Heruntergeladen von manualslib.de
430 x 255 x 250 mm
5.5 kg
6.0 kg
430 mm
457 mm
yes
Special saw chain Oil
0.26l
3/8"
1.27 mm
Oregon 91PX062X
7
3/8"
yes
Oregon
180SDEA095
22 m/s
1 cylinder 2 stroke
air-cooled
46 cm³
2.0 kW
3300±200 min
-1
11000 min
-1
0.55 l
Mix 40:1
Handbücher-Suchmachiene
Keep the noise emissions and vibrations to a
minimum.
Wear hearing protection.
The effects of noise can cause hearing damage.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Measured sound pressure level L
Uncertainty K
pA
Guaranteed sound power level L
Measured sound power level L
Uncertainty K
wA
Vibration Front handle
Vibration Rear handle
Uncertainty

7. Before starting up

m CAUTION!: Start the engine only when the saw is
fully assembled and checked.
m ATTENTION!: Always wear high-strength
gloves when handling the saw chain or adjust-
ing it.
Assembling the bar, and the chain (Fig. 3-6)
Open the packaging and assemble the bar and chain
as follows:
1. Press the front hand guard back (Fig. 14/Pos. 3a)
so that the chain brake is disabled.
2. Loosen the two nuts (B) and remove the cover
(17) and spacer (A).
3. Mounting the stopper claw (Fig. 11)
Insert the stopper claw (19) into the recesses of
the housing (see Fig. 11) and secure with the 2
fixing screws (A). Use the tool supplied with the
assembly tools (10).
4. Mount the bar on the two threaded pins (Fig. 4)
5. Slide the chain around the sprocket, next slide
the saw chain around the bar. Pay attention to the
installation direction of the chain. (Fig. 4-5)
6. Insert the chain tensioning screw (Z) into the low-
er hole of the chain bar (Y). (Fig. 4)
7. Install the cover (17) and tighten the nuts (B) by
hand.
99 dB(A)
pA
3 dB
114 dB(A)
wA
109.9 dB(A)
wA
3 dB
7.5 m/s²
7.0 m/s²
1.5 m/s²