Remaining Risks; Technical Details - Scheppach 5910114903 Originalbetriebsanleitung

A kickback is caused by incorrect use or misuse. It
can be avoided by taking proper precautions as given
below.
■ Hold the saw firmly with both hands, with your
thumb and fingers around the handles of the chain-
saw. Hold your body and arms in a position in
which you can withstand kickback forces. If suit-
able measures are taken, the operator can control
the recoil forces. Never let go of the chainsaw (see
fig. E).
■ Avoid an abnormal posture and do not saw over
shoulder height. This will prevent inadvertent con-
tact with the tip of the rail and allows a better control
of the chainsaw in unexpected situations.
■ Always use the replacement rails and saw chains
specified by the manufacturer. Incorrect replace-
ment rails and saw chains can lead to a tearing of
the saw chain and/or kickback.
■ Follow the manufacturer's instructions for sharp-
ening and maintenance of the saw chain. Setting
the depth limiter too low can increase the risk of
kickback.
■ Do not saw with the tip of the blade. This can lead
to a kickback.
■ Make sure that there are no nails or pieces of metal
in the cutting area. Pay particular attention to nails
and pieces of iron in the area of the cut. Also be
careful when cutting hardwoods in which the chain
could jam. This can lead to a kickback.
■ Start the cut using full power and keep the chain-
saw at top speed while sawing.
■ Ensure that there are no objects on the ground that
you can trip over.

6.9 Remaining risks

m DANGER
RISK OF INJURY !
Contact with the saw-chain can lead to fatal cutting
injuries.
Never put your hands into the running saw-chain.
RISK OF KICKBACK !
Kickback can lead to fatal cutting injuries.
RISK OF BURNING !
The chain and the guide bar heat up during operation.

7. Technical details

Weight empty tank, no
cutting equipment approx.
Weight empty tank, with
cutting equipment approx.
Fuel tank
Tank for chain lubrication
oil
5.65kg
7.0 kg
approx. 550 cm (0.55 l)
3
approx. 260 cm (0.26 l)
3
www.scheppach.com
Usable cutting length*/
guide rail
Max. chain speed
Chain pitch
Drive link thickness
Saw chain model
Guide rail model
Number of teeth/division
Cylinder capacity
Max. motor output ac-
cording to ISO 7293
Idle speed n
0
Speed n
max
Spark plug
* The actual cutting length may be lower than the
specified cutting length.
Noise
Sound pressure level L
pA
according ISO 22868
Uncertainty K
pA
Sound power level L
WA
according ISO 22868
Uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
The above-mentioned noise emission values were
measured in accordance with a standardised test
procedure and can be used to compare one power
tool with another.
The above-mentioned noise emission values can
also be used for the preliminary assessment of ex-
posure.
Vibration
Vibration value on the rear
handle according ISO 22867
Vibration value on the front
handle according ISO 22867
Uncertainty K
m WARNING
You can reduce the vibration risk, e.g. the risk of Ray-
naud's phenomenon (circulatory problems), by taking
regular breaks during which you rub your hands to-
gether.
47 cm (20")
22 m/s
8.255 mm (0.325")
1.5 mm (0.059")
Oregon
21BPX078X
Oregon
208PXBK095
7 teeth/8.255 mm
(0.325")
56 cm
3
2.3 kW
3100 ± 300 rpm
11000 rpm
L8RTC
99,6 dB(A)
3 dB
110.3 dB(A)
3 dB
6.38 m/s
2
6.72 m/s
2
1.5 m/s
2
GB | 33