Residual Risks; Technical Data - Scheppach HS110 Bedienungs- Und Sicherheitshinweise

10. Before using any of the tools, ensure that all protective de-
vices are correctly attached.
11. Before use, ensure that all of the tools used by you full the
technical requirements of this power tool and are properly
attached.
12. The saw blade supplied should only be used for sawing
wood and never for working metal.
13. Use the saw blade intended for the material to be pro-
cessed.
14. Use only a saw blade with a diameter that matches the
specifications on the saw.
15. Use only saw blades that are marked with an equal or
higher rotational speed than that marked on the power
tool.
16. Use only saw blades recommended by the manufacturer
which conform to EN 847-1, if intended for cutting wood
or similar materials.
17. Wear suitable personal protective equipment, such as:
– hearing protection;
– protective gloves when handling saw blades.
18. Use only saw blades recommended by the manufacturer
which conform to EN 847-1. Warning! When changing
the saw blade, make sure that the cutting width is not small-
er and the thickness of the saw blade is not greater than
the thickness of the splitter.
19. When sawing wood and plastics, avoid overheating the
saw teeth. Reduce the feed speed to avoid the plastic melt-
ing.

Residual Risks

This power tool has been constructed in accord-
ance with the latest technology and the generally
recognised safety regulations. Nevertheless, it is
possible that individual residual risks may occur
during operation.
• Electrical hazard if improper electrical connection cables are
used.
• In addition, concealed residual risks may be present in spite
of all the precautions that have been taken.
• Residual risks can be minimised by observing the „Safety
instructions" and „Use in accordance with the designated
purpose", as well as the operating instructions.
• Do not put any unnecessary stresses on the machine: exces-
sive pressure during sawing will quickly damage the saw
blade. This may result in a reduction in the performance of
the machine, as well as a reduction in the cutting accuracy.
• Avoid switching the machine on by accident: when insert-
ing the plug into the socket, the power button must not be
pressed.
• Use the tool which is recommended in this manual. This will
ensure the optimal performance of your saw.
• Keep your hands away from the working area when the ma-
chine is in operation.
• Before you carry out any adjustments or servicing work, turn
the device off and remove the mains plug.
8 GB/CY

7. Technical data

AC motor
Power
Operating mode
Idle speed
Hard metal saw blade
Number of teeth
Riving knife thickness
Min. workpiece dimensions
W x L x H
Table size
Cutting height max. 90°
Cutting height max. 45°
Height adjustment
Tilting saw blade
Suction connection
Weight approx.
* Operating mode S6 40%: Continuous duty with intermittent
loading (operating time 10 min.). In order avoid impermissible
overheating of the motor, the motor should be driven for only
40% of the operating time with the stipulated nominal power
and must then continue to run with no load for the remaining
60% of the operating time.
Noise
The total noise values were determined in accordance with
EN 62841.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total vibration
values (vector sum - three directions) determined in accordance
with EN 62841.
NOTE: The specified device emissions values have been meas-
ured in accordance with a standardised test procedure and
can be used for comparison of one electric tool with another.
The specified device emissions values can also be used for an
initial estimation of the load.
230 V ~ 50Hz
2000 Watts
S6 40% *
4800 min
-1
ø 254 x ø 30 x 2,8 mm
24
2,5 mm
10 x 50 x 1 mm
546 x 630 mm
87 mm
55 mm
0 - 87 mm
0 - 45°
ø 40 mm
21/22 kg
93,5 dB(A)
3 dB
106,5 dB(A)
3 dB