Technical Specifications - Ferm FZT-250N Gebrauchsanweisung

REF.NR. DESCRIPTION
407820 POWER SWITCH
407821 GEAR
407402 LIFTINGWHEEL COMPLETE
407428 LOCK HANDLE
407405 RUTARY MARK
407822 MOTOR
407838 LIFT THREAD SPINDLE COMPLETE
407823 SPINDLE COMPLETE
407824 SPINDLE LOCK COMPLETE
407826 RIVING KNIFE SUPPORT
407827 FILLING PLATE
407828 LOCATION PIN
407408 FLANGE
407830 NUT M16
407411 ANGLE GAUGE COMPLETE
407831 LOCKING KNOB
407829 LOCKING KNOB
407825 CLAMPING LEVER
407832 SAWGUIDE COMPLETE
407833 TABLE INSERT
407414 RIVING KNIFE COMPLETE
407834 PROTECTION COVER SAW
407835 SET OF SCREWS FOR FLOORSTAND
407836 COVERS OF TABLE FEET
806202 BALL BEARING 6202 ZZ
806204 BALL BEARING 6204
407837 MOTOR HOUSING (FRONT)
58
SPARE PARTS
016 T/M 019 + 023
025 T/M 028
032 T/M 040
040 T/M 045
078 T/M 085
086 T/M 106
109 T/M 113
114 T/M 119
DRAW.2 REF.A
DRAW.2 REF.B
DRAW.2 REF.D
38 Use only saw blades recommended by the manufac-
turer. Do not use blades with a max. rated speed lower
FERM NR.
than the rated speed of the machine. Only use saw
001
blades which comply with EN-847-1
39 Take care that the selection of the saw blade depends
015
on the material to be cut.
40 Connect circular saws to a dust-collecting device
020
when sawing.
41 Use and correct adjustment of the riving knife
023
42 Use and correct adjustment of the upper saw blade
024
quard.
43 Take care when slotting.
44 Do not use the machine for cutting fire wood.
SWITCH OFF THE MACHINE IMMEDIATELY WHEN
050 YOU DISCOVER:
1 A defective mains plug or mains lead;
051
2 A defective switch.
052
3 Overheating of the machine.
4 Smoke or odeur caused by scorched insulation.
057
058
085
086
089
107 + 108
Ferm Ferm

TECHNICAL SPECIFICATIONS

Voltage | 230 V~
Frequency | 50 Hz
Power input | 1100 W
No load speed | 2950/min.
Saw blade dimensions | 250x30 mm
Number of teeths | Z30
Max. saw capacity 90º | 58 mm
Max. saw capacity 45º | 51 mm
Measurements of bench | 660x865 mm
(table including table extensions)
Suction mouth | 65 mm
Weight | 36 kg
L pa (sound pressure level) | 91.1 dB(A)
L wa (sound power level) | 101 dB(A)
Electrical safety
Always check that the power supply corre-
sponds to the voltage on the rating plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
- As a supply for this machine always use an unloaded
line and/or an extension cable with conductors of at
least 1,5 mm 2 and protected with a 16 A fuse. Be sure
that this extension cable is not longer than 20 metres.
- Only connect your machine and/or extension cable to
an earthed electricity mains.
- This machine can be switched to the single-phase
network (230 V~/50 Hz). If you are in doubt about the
earth of the electricity provisions, consult an electri-
cian first.
3