Maintenance - Ferm FZT-250N Gebrauchsanweisung

ı
( DK )
CE
KONFORMITETSERKLÆRING
Vi erklærer at under almindeligt ansvar, at dette
produkt er i overenstemmelse med følgende
normer eller normative dokumenter
EN61029-1, IEC1029-2-1,
EN55014-1, EN55014-2
EN 61000-3-2, EN 61000-3-3
i henhold til bestemmelserne i direktiverne:
98/37/EØF, 73/23/EØF,
89/336/EØF
Approved by TÜV-Rheinland, Product Safety GmbH,
Certificate Numbers: S2 2030152
01-06-2000
GENEMUIDEN NL
G.M. Ensing
Quality department
54
MALFUNCTIONS
In the case that the machine is not functioning properly,
we give a number of possible causes and appropriate
solutions below.
1 THE MOTOR DOES NOT START
- the plug is not in the mains
- the cable has been interrupted
2 THE WORKPIECE IS JAMMING AGAINST THE
RIVING KNIFE DURING PROCESSING
- the saw blade must be aligned (see manual)
3 THE SAW CUT IS NOT SMOOTH (FRAYED)
- the saw blade must be sharpened
- the saw blade has been assembled back-to-front
- the saw blade has become coated with resin or saw-
dust
- the saw blade is not suitable for this process
4 THE WORKPIECE IS TOUCHING THE BACK OF
THE SAW BLADE AND IS JUMPING OUT
- the riving knife must be aligned (see manual)
- the fence is not being used
- the saw blade is thicker than the riving knife or the
riving knife is not being used
- the saw blade must be sharpened
- the workpiece has not been kept in its place until after
sawing
- the tension button of the cross-cut fence is loose
5 THE HEIGHT ADJUSTMENT/MITRE ADJUST-
MENT HANDLE AND/OR MITRE LOCKING HAND-
LE IS BLOCKED
- sawdust and dust must be removed
6 THE MOTOR HAS DIFFICULTY REA-CHING THE
MAXIMUM NUMBER OF REVOLUTIONS
- the extension cable is too thin and/or too long (see
manual)
- the mains voltage is lower than 230 V
7 THE MACHINE IS VIBRATING
- the machine has not been fastened onto the workben-
ch
- the frame is not level with the floor
- the saw blade has been damaged
Let the saw do the job. Do not put undue pres-
sure on the circular saw.
Ferm Ferm

MAINTENANCE

Make sure that the machine is not live when car-
rying out maintenance work on the motor.
The Ferm machines have been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
machine care and regular cleaning.
Cleaning
Keep the ventilation slots of the machine clean to prevent
overheating of the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.
If the dirt does not come off use a soft cloth moistened with
soapy water. Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may damage the
plastic parts.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please con-
tact your local Ferm dealer.
In the back of this manual you find an exploded view
showing the parts that can be ordered.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these mate-
rials to the appropriate recycling locations.
Take your unwanted machines to your local Ferm-dealer.
Here they will be disposed of in an environmentally safe
way.
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
7