Safety Instructions - Ferm TSM1005 Gebrauchsanweisung

SPARE PARTS LIST FBS-205/1000
REF NR DESCRIPTION
407680 RULER
407557 SQUARE NUT
407455 KNOB
407555 MOVABLE QUARD
407681 SUNK SCREW M3 X 12
407560 TABLE INSERT
407558 RIVING KNIFE
407682 HANDLE LOCK SCREW
407683 NUT M12
407553 FIXING GUARD
407552 OUTER FLANGE
407551 INNER FLANGE
407684 STAND BAR
407559 SWITCH
407763 MOTOR 1000 WATT
78
FERM NR
001
CIRCULAR SAW TABLE
002
003
TECHNICAL SPECIFICATIONS
004 - 008
009 Voltage
Frequency
010
Power consumption
014 - 018
Unloaded speed
022
Saw blade dimensions
023
Max. saw capacity 90º
024
Dust extractor diameter
Mitre setting
027
Weight
030
Lpa (sound pressure)
Lwa (sound power level)
034
036
CONTENTS OF THE PACKAGE
038
1 Circular saw table
1 Saw blade
1 Push stick
1 Rip fence
1 Instructions

1 Safety instructions

1 Warranty card
Check the machine and accessories for transport
damage.
PRODUCT INFORMATION
Fig. 1
1. Work table
2. Guard
3. Push stick
4. Saw blade
5. Riving knife
6. Insert plate (plastic)
7. On/Off switch
8. Motor
9. Mains cable
10. Underframe
11. Rip fence
12. Locking button
13. Protractor gauge
14. Bolt for guard
15. Nut for guard
Ferm Ferm
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
| 230 V~
| 50 Hz
| 1000 W
Carefully read this manual before using the machine.
| S3 40% 10 min
Make sure that you know how the machine functions and
| 2950 rpm
how to operate it. Maintain the machine in accordance
| 205x2.7x16 mm
with the instructions to make sure it functions properly.
| 43 mm
Keep this manual and the enclosed documentation with
| 31 mm
the machine.
| 0-45°
| 14 kg
ELECTRICAL SAFETY
| 85 dB(A)
Attention! When electrical tools are used the
| 105 dB(A)
following safety measures must be observed against
the danger of electric shock, injury and/or fire. Read
and pay close attention to these recommendations
before using a machine.
Always check that your mains voltage is the same
as the value on the type plate.
When replacing cords or plugs
Throw away cords or plugs as soon as they are replaced
by new ones. It is dangerous to insert the plug of a loose
cord into the wall socket.
When using extension cords
Only use an approved extension cord that is suitable for
the power consumed by the machine. The cores must
have a cross-section of at least 1.5 mm
cord is on a reel, unroll the cord completely.
When using electrical machines, always observe
local safety regulations so as to prevent fire danger,
danger of electric shocks and personal injury. It is
therefore important to read not only the following
instructions, but also the safety regulations set out
in the enclosed safety leaflet.
Keep the instructions in a safe place!
SPECIFIC SAFETY REGULATIONS
• A circular saw table must be adequately and
effectively illuminated. If fluorescent lighting is used,
the "stroboscope" effect must be taken into account.
This can make a rotating saw blade look as though it is
stationary. This can be solved by using double fittings
and creating a phase shift between the two
fluorescent tubes.
• Check the following:
• Does the connection voltage of the motor and any
protective circuit switch match the mains voltage?
(Machines designed for a mains voltage of 230V can
safely be connected to a mains voltage of 220V).
• Are the mains cord and the mains plug in good
condition? (Sturdy, not frayed and undamaged).
2 . If the extension
3