Herunterladen Inhalt Inhalt Diese Seite drucken
Inhaltsverzeichnis

Werbung

GB
Equipment check
D
Warning! Use only FERM approved attachments. Serious injury may result from the use of a non-approved attachment
combination. FERM will not be responsible for the failure of cutting devices, attachments or accessories which have not been
tested and approved by FERM. Please read and comply with all safety instructions listed in this manual and safety manual.
NL
Check the hedge trimmer for loose/missing nuts, bolts, and screws. Tighten and/ or replace as needed.
Inspect fuel lines, tank, and the area around the carburettor for fuel leaks. Do not operate the hedge trimmer if leaks are found.
Inspect the shield for damage. Ensure that the blade stiffener is securely in place.
F
Replace if either is damaged or missing.
Check that the cutting attachment is firmly attached and in safe operating condition.
Check that the blade stiffener is not damaged or distorted and replace the blade stiffener if it is bent or damaged.
E
3 . OPERATION
P
Fuel Requirements
Petrol
Use 89 Octane [R+M/2] (mid grade or higher) petrol known to be good quality. Petrol may contain up to 15% MTBE (methyl tertiary-butyl
ether). Petrol containing methyl (wood) alcohol is not approved.
Two Stroke Oil
Atwo-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC standards must be used. Engine problems due to inadequate
lubrication caused by failure to use an ISOLEGD and J.A.S.O. FC certified oil will invalidate the two-stroke engine warranty. (Emission
related parts only are covered for two years, regardless of two stroke oil used, per the statement listed in the Emission Defect Warranty
Explanation.)
Fuel to oil mix 25:1 ratio
Gas in liters
4
8
20
Important: Regardless of the mixing ratio mentioned in the corresponding manuals, premium grade 2-cycle oil can be used for all previously
built Ferm engines.
Handling Fuel
Warning! Fuel is very flammable. Use extreme care when mixing, storing or handling or serious personal injury
could result.
Use an approved fuel container.
Do not smoke near fuel.
Do not allow flames or sparks near fuel.
Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalise.
Never refuel the hedge trimmer when the engine is hot or running!
Do not fill fuel tanks indoors. Always fill fuel tanks outdoors over bare ground.
Do not overfill fuel tank. Wipe up spills immediately.
Securely tighten the fuel tank cap and close fuel container after refueling.
Inspect for fuel leakage. If fuel leakage is found, do not start or operate the hedge trimmer until leakage is repaired.
Move at least 3m (10 ft.) from the refueling location before starting the engine.
Mixing Instructions
Fill an approved fuel container with half of the required amount of petrol.
Add the correct amount of 2-stroke oil to petrol.
Close container and shake to mix oil with petrol.
Add remaining petrol, close fuel container, and remix.
Spilt fuel is aleading cause of hydrocarbon emissions. Some countries may require the use of automatic fuel shut-off containers to reduce fuel spillage.
After use
Do not store the hedge trimmer with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.
Storage
Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved,
airtight container. Store in a well ventilated, unoccupied building away from sparks and naked flames.
Important: Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added.
Important: Stored two-stroke fuel may separate. Always shake the fuel container thoroughly before each use.
12
Aparar sebes
Fig. 7
4. MANUTENÇÃO
O aparador de sebes foi concebido para proporcionar muitas horas de funcionamento sem problemas. Uma manutenção regular
programada do aparador de sebes permite atingir esse objectivo. Se não tiver a certeza ou não dispuser das ferramentas necessárias, deve
enviar o aparador para a morada indicada no cartão de garantia para ter assistência. Foi atribuída uma classificação a cada tarefa de
manutenção, para ajudá-lo a decidir se pretende reparar o equipamento sozinho ou enviá-lo para a assistência. Se uma tarefa não estiver
incluída, envie o equipamento a reparar para a morada indicada no cartão de garantia.
Nível de experiência
Nível 1 = Fácil de reparar. Amaioria das ferramentas necessárias é fornecida com o aparador de sebes.
Nível 2 = Dificuldade média. Podem ser necessárias algumas ferramentas específicas.
Nível 3 = É necessário experiência. São necessárias ferramentas específicas. AFerm recomenda que o aparador de sebes a reparar seja
Oil in cc.
160
320
AFerm oferece kits e peças de manutenção para que o trabalho de manutenção seja mais fácil. Abaixo de cada título de tarefa são
800
apresentadas as várias referências necessárias para a respectiva tarefa. Veja a morada indicada no cartão de garantia relativo a estas
peças.
Intervalos de manutenção
Procedimentos de manutenção da assistência
Componente/
Sistema
Saída de
exaustão do
cilindroInspect/
Clean/
Afiar lâminas
Ferm
Ferm
Aviso! Se o motor não parar depois de colocar o botão de paragem na posição "STOP" (Parar), feche o obturador (posição de
arranque a frio) para parar o motor. Para reparar o botão de paragem do aparador de sebes, envie-o para o nome e morada
indicada no cartão de garantia.
Segure o aparador com firmeza e carregue no gatilho de aceleração para aumentar a velocidade do motor.
Incline o aparador para que os dentes de corte fiquem ligeiramente inclinados na direcção da sebe ou arbusto e inicie o corte.
Aviso! Nunca retire as mãos do aparador de sebes quando as lâminas estiverem em movimento.
Aviso! O motor continua a funcionar, mesmo se as lâminas tiverem parado devido a um obstáculo. Se isto ocorrer, pare o motor,
desligue o cabo de ignição e retire o obstáculo.
enviado para a morada indicada no cartão de garantia.
Procedimento
Nível de
Utilização
de manutenção
habilitação
diária ou
necessário
anterior
Inspeccionar/
3
Limpar/
Descarbonizar
Inspeccionar/
3
I (2)
Limpar
Durante cada
3 meses ou
6 meses ou
Anualmente
abasteciment
90 horas
270 horas
ou 600 horas
o
-
-
I C
-
-
-
-
GB
D
NL
F
E
P
-
-
77

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Fpht-26cc

Inhaltsverzeichnis