Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
English
Before electrical re-connection, check
that the appliance is electrically safe.
Note - References to LH and RH
oven apply as viewed from the front.
1
To Remove the Control Panel
Disconnect the appliance from the
electricity supply. Remove the pan
supports and control knobs. Remove
the 3 screws at the rear of the top
edge of the control panel.
Open the oven doors and remove the
2 fixing screws, one at each end, un-
derneath the control panel. Lift the
control panel, pull forward and dis-
connect the wiring from the rear.
Replace in reverse order.
A Control panel top fixing screws
B Hotplate front fixing screws
C Hotplate back fixing screws
2
To Remove the Hotplate top
Disconnect the appliance from the
electricity supply. Pull cooker forward
to gain access.
Remove the control panel see 1. Re-
move the hotplate burner caps and
tops. If there are screws holding the
hotplate burners to the hotplate, re-
move them (not the spark electrode
fixing screws). Remove the 2 hexa-
gon headed rear hotplate fixing
screws and the 3 front hotplate fixing
screws. Lift the hotplate clear of the
appliance. Replace in reverse order.
3
To Remove an Outer Side
Panel
Disconnect the appliance from the
electricity supply. Remove the control
panel – see 1. Remove the retaining
screw on the upper front edge and the
two fixings on the rear or the side
panel. Undo the lower retaining screw
situated below the edge at the panel
front corner. Remove the panel by
pulling it away from the unit.
4
To Remove an Oven Neon
Remove the control panel – see 1.
Hold the lens in position at front of the
panel and from the rear pull the body
of the neon out of the front lens. Hold
the front lens in position and from the
rear of the control panel fit the new
light to the lens. Replace parts in re-
verse order. Ensure the replacement
neon functions correctly.
5
To Remove the Clock
Remove the control panel - see 1.
Pull off the timer control button(s).
Remove the timer/mounting bracket
assembly from the facia by removing
the fixing screws. Remove the timer
from its mounting bracket by depress-
ing the plastic lugs on the timer case,
at the same time pulling the unit for-
ward. Reassemble in reverse order.
When replacing leads refer to the wir-
ing diagram. Check operation of
timer.
6
To Remove a Thermostat
Disconnect the appliance from the
electricity supply. Remove the hot-
plate – see 2. Open the appropriate
oven door and remove the oven
shelves.
RH oven
Remove the two fixings that secure
the thermostat phial cover. Unclip the
thermostat phial from the clips in the
oven back panel.
LH oven
Remove the two screws holding the
thermostat phial to the oven fan cover
at the rear of the oven. Pull the unit
forward to access the rear of the
cooker. Remove the both cover
boxes by removing the fixing screws
and lifting clear. Feed the thermostat
capillary clear of the oven. Discon-
nect the wires from the thermostat
and undo the two fixings that secure
the control to the mounting plate. Fit
the replacement and re-assemble in
reverse order. Ensure that the phial is
clipped to the oven rear, positioned
centrally between the clips. Check
that the thermostat functions cor-
rectly.
7
To Remove an Oven element
Thermal Cut-Out.
Disconnect the appliance from the
electricity supply. Pull the cooker for-
ward to gain access to the cover box.
Undo the cover screws and lift clear.
The cutout is located on the earth
plate beside the oven element con-
nections. Disconnect the cutout wir-
48
ing. Undo the fixings that secure the
cutout to the earth plate and remove.
Fit replacement control and re-as-
semble in reverse order.
8
To Remove a Hotplate Tap
Remove the hotplate – see 2. Unplug
the FSD lead from the rear of the tap.
Undo compression fitting at the rear
of the tap. Remove the fixings that se-
cure the tap to the gas rail. Discon-
nect the ignition switch wiring. Re-
move the tap. Remove and discard
the gasket seal. Fit new gasket seal to
replacement tap. Re-assemble in re-
verse order. Check the appliance is
gas sound. Check hotplate ignition.
9
To Change an Ignition Switch
Change the gas tap - see 7.
10 To Remove a Hotplate Burner
Injector
Remove the hotplate - see 2. Remove
the injector directly from the burner
body. Fit the appropriate injector. Re-
assemble in reverse order. Check the
appliance is gas sound.
11 To Remove a Hotplate Burner
Spark Electrode
Remove the pan supports, burner
heads and caps. Remove the screw
holding the electrode to the burner
body. Lift up the electrode and dis-
connect the lead.
Note
Take care to prevent the ignition wire
from falling back through the clear-
ance hole.
Fit the lead to the new electrode and
reassemble in reverse order and
check correct burner ignition.
12 To Remove an Oven Door
Open the oven door. Support the door
and remove the two screws that se-
cure the upper hinge to the front
frame of the unit. Remove the door
from the lower hinge by lifting slightly
and moving it outward. Re-assemble
in reverse order.
Werbung
Inhaltsverzeichnis
