Troubleshooting - WMF Profi Plus Gebrauchsanweisung

Allow the parts to dry completely before reassembling them.
After drying, lightly oil the grates (13, 14, 15), the roll blade (16), the cross blade (17) and the feeding
screw (9) with vegetable oil.
CLEANING THE PARTS
dishwasher safe
Mincer casing (1)
Mincer attachment (2)
Filling bowl (4)
Display (5)
Threaded ring (6)
Control knob (7)
Stopper (8)
Feeding screw (9)
Grates storage (10)
Cover for grates storage (12)
Grates (13, 14, 15)
Roll blade (16)
Cross blade (17)
Cutting disc (18)
Sausage attachment (19, 20)
Kibbeh attachment (21)
Shortbread biscuit attachment (23,24)
Cleaning aid for grates (22)
34
rinse under wipe with a
running water damp cloth

9 | TROUBLESHOOTING

If any of the problems listed in the table persist, contact WMF Customer Service.
PROBLEM POSSIBLE CAUSE
Food gets stuck in Food was pushed into the
the feeding screw filler neck with too much
pressure
The feeding screw Food was pushed into the
is blocked repeat- filler neck with too much
edly pressure
The meat mass is The grate is too big and/
not fine enough or the ingredients have not
been minced a sufficient
number of times
The motor stops The overload protection has
during operation possibly switched off the
motor
The feeding screw The threaded ring (6) has
wobbles during come loose
operation
The motor auto- Possibly the motor is
matically switches overloaded
to the reverse
function for about
5 seconds
The ingredients The threaded ring (6) is not
are leaking out fitted correctly. It is sitting
on the side of the too loosely on the mincer
threaded ring (6) attachment (2)
Rapid wear of the The threaded ring (6) has
cros blade and been tightened too much
the grates. Note: and / or the mincer has been
Normal wear and operated in empty mode.
tear of the grates
(13, 14, 15) and
the cross blade
(17) may occur.
SOLUTION
Briefly press the reverse button (a) to release the
blockage and then continue with the mincing
process
Switch off the appliance and pull the mains plug
out of the socket. Remove the mincer attachment
(2) and the feeding screw (9) and remove the
blockage. Then reassemble the appliance according
to the instructions and restart it.
Use a finer grate and/or mince the meat mass
several times in a row
Switch the appliance off by turning the control
knob (7) to "0". Pull the mains plug out of the
socket, disassemble and clean the appliance accord-
ing to the "Cleaning and care" instructions. Let the
appliance cool down for approx. 30 minutes
Switch off the appliance and then screw the
threaded ring (6) clockwise. Caution! Do not
overturn or overtighten the threaded ring (6)!
If this happens three times in a row, the motor
stops and the cleaning symbol lights up.
Disconnect the power plug from the socket. Disas-
semble and clean the appliance according to the
"Cleaning and care" instructions
Switch off the appliance and then screw the
threaded ring (6) clockwise. Caution! Do not over-
turn or overtighten the threaded ring (6)! If this
does not solve the problem, disassemble and clean
the appliance according to the "Cleaning and care"
instructions
The threaded ring (6) must never be tightened. And
the mincer must never be operated in empty mode,
i.e. without meat in the appliance! This leads to
overheating of the grate and the blade and thus
promotes wear of these parts!
Care instructions: After drying, lightly oil the grates
(13, 14, 15), the roll blade (16), the cross blade (17)
and the feeding screw (9) with vegetable oil for
care.
35