Bosch 0 607 453 Serie Originalbetriebsanleitung Seite 23

OBJ_BUCH-1654-005.book Page 22 Friday, September 16, 2016 1:20 PM
22 | English
82 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
0 607 454 0../2..:
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K = 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
(triax vector sum) and uncertainty K
Vibration total values a
h
determined according to EN 28927.
Screwdriving without impact: a < 2,5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN ISO 11148 and may be used to compare one
pneumatic tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the pneumatic tool. However if the pneumatic
tool is used for different applications, with different accesso-
ries or insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase the expo-
sure level over the total working period.
An exact estimation of the level of exposure to vibration
should also take into account the times when the pneumatic
tool is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level over
the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintaining the pneu-
matic tool and the accessories, keeping the hands warm, or-
ganisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical data" complies with all applicable
provisions of the directive 2006/42/EC including its amend-
ments and is in conformity with the following standards:
EN ISO 11148-6.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ECS
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Devices for Safe Handling
Pneumatic tools that are operated with a torque > 4 Nm, must
be equipped with an auxiliary handle or fastened in a clamping
fixture via the clamping area 4.
1 609 92A 37K | (16.9.16)
 If you want to operate the pneumatic tool in a suspen-
sion device or a clamping fixture, take care to fasten it
in the device/fixture first before connecting it to the air
supply. This measure prevents accidental starting of oper-
ation.
Make sure that the auxiliary handle or the clamping fixture
holds the pneumatic tool securely and firmly.
Do not overload the clamping area.
Suspension Device
2 2
, K=1,5 m/s .
With the utility clip 7, you can fasten the pneumatic tool to a
suspension device.
 Regularly check the condition of the utility clip and the
hook of the suspension device.
Clamping Fixture
– The pneumatic tool can be mounted in a clamping fixture
over the mentioned clamping area 4. If possible, utilise the
entire clamping area. The smaller the clamping area, the
stronger the clamping forces act.
Auxiliary Handle
– Slide the auxiliary handle 10 onto the clamping area (col-
lar) 4.
The auxiliary handle 10 can be set to any position for a secure
and low-fatigue working posture.
– Turn the wing bolt for adjustment of the auxiliary handle in
anticlockwise direction and set the auxiliary handle 10 to
the required position. Then tighten the wing bolt again in
clockwise direction.
Exhaust-air Guidance
With exhaust-air guidance, the exhaust air can be diverted
through an exhaust-air hose away from your workplace, while
at the same time achieving optimal sound-proofing. Addition-
ally, your working conditions are improved, as your workplace
can no longer be contaminated though oil-containing air and
dispersed dust or chips.
Centralised Exhaust-air Guidance (see figure A)
– Loosen hose clamp 12 of supply-air hose 13, mount the
supply-air hose to hose fitting 6 and retighten the hose
clamp.
– Work the exhaust-air hose (centralised) 11, which con-
ducts the exhaust air away from your workplace, over the
supply-air hose 13. Then connect the pneumatic tool to
the air supply (see "Connecting the Air Supply", page 23)
and work the exhaust-air hose (centralised) 11 over the
mounted supply-air hose onto the end of the pneumatic
tool.
Connecting the Air Supply
For maximum performance, the values for the inner hose di-
ameter as well as the connection threads must be adhered to
as listed in the "Technical Data" Table. To maintain the full
performance, only use hoses with a maximum length of 4 m.
The compressed air supplied should be free of foreign materi-
al and moisture to protect the tool from damage, contamina-
tion, and the formation of rust.
Autogoods "130"
Bosch Power Tools