Programming - Comunello LIMIT 500 ONE Installations- Und Gebrauchsanleitung

1 2 3 4 5 6 7 8 9 10
Programming buttons
AUTOSET Maximum Stroke Programming
CAUTION: Always check the operator rotation direction (Operator 1)
before running the maximum stroke self-learning procedure. Always start
the self-learning procedure with the barrier half open.
CAUTION: Before starting operator movement for maximum stroke self-
learning procedure, the control unit screens the system for any accessories
installed on the digital BUS line. This operation can delay the actual
operators' movement.
CAUTION: To check the correct programming of the stroke, you can also
use the STEP BY STEP button as AUTO-PP command (open-close).
CAUTION: CAUTION: During the maximum stroke self-learning procedure,
make sure that the barrier manoeuvring area is free.
RADIO CONTROL PROGRAMMING
The control unit enables the memorisation of radio controls with different
codes, for both fixed and rolling code versions.

Programming:

Programming (and storage) of the transmission code is done by pressing
the TX CODE button and checking the status of the corresponding LED
(above the TX CODE button) as follows:
1. Press the TX CODE button once: the corresponding led flashes once
(1010). If a button code is sent from the transmitter, and the code is valid, it
will be saved with AUTO-PP function (open-close).
2. Press the TX CODE button twice: the corresponding led flashes twice
(110110). If a button code is sent from the transmitter, and the code is valid,
it will be saved with PED function (pedestrian).
3. Press the TX CODE button three times: the corresponding led flashes
three times (11101110). If a button code is sent from the transmitter, and
the code is valid, it will be saved with AUX function (2nd auxiliary channel).
Deletion:
Deletion of all the radio codes is done by pressing the TX CODE button and
checking the status of the corresponding LED (above the TX CODE button)
with the following association:
1. Press the TX CODE button four times: the corresponding led lights up
permanently (steady). To confirm the deletion, press the TX CODE button
again (the corresponding led starts to flash) and keep it pressed until the led
stops flashing, which confirms the successful deletion of all codes saved
in the system.
1 2 3 4 5 6 7 8 9 10
Programming buttons
TX CODE Remote control programming
ACCESSORIES DETECTION (BUS LINE)
The control unit automatically detects all the ONE accessories wired on
the BUS line, checking the type of accessory, its numeric identifier ID and
the type of operation set (MODE). Always make sure to use accessories
with different ID for each type of accessory (par: ACCESSORY ADDRESS
ASSIGNMENT). The system also detects the accessories installed on the
BUS line:
46
COMUNELLO ®Copyright 2015 - All right reserved
1 Before the maximum stroke self-learning process (AUTOSET). At this
stage, the system detects the accessories installed and saves the
system configuration (e.g.: new installation).
2 Each time you press the RESET button. At this stage, the system re-reads
the accessories installed, but does not change the initial configuration
(accessories saved).
CAUTION: The detection of the accessories is an automatic operation
that may cause a delay in the system's configuration proportionate to the
number of accessories installed.
CAUTION: Make sure you have set the ID and MODE (operating mode)
on all accessories installed, before connecting them to the digital BUS line.
IMPORTANT! If the system is configured with access via the app
COMUNELLO ONE (requiring use of a wifi tablet and access key
K-ONE (code no. ONE KEY), leave the MODE dip switches set to
OFF (operation TYPE 1) on all accessories connected to the BUS.
SETTINGS VIA THE APP COMUNELLO ONE
The control unit is equipped with an additional advanced access for system
configuration. Using the accessory (optional) K-ONE (code no. ONE KEY)
the user can connect the control unit via WiFi radio and proceed with total
and simple configuration, guided by the application COMUNELLO ONE
downloadable from the online stores. The app COMUNELLO ONE requires
use of a WiFi device (tablet or smartphone), Android or iOS.
Connector for K-ONE module
Configuration via the COMUNELLO ONE app allows you to configure and
adjust all the parameters of the system in a fast and easy way, monitor its
operation, manage the list of saved remote controls, copy the configuration
to another equivalent system and plan maintenance.
ADDITIONAL ADJUSTMENTS FROM THE APP:
Guided procedure to check direction of rotation of the operators and
change their settings.
1 2 3 4 5 6 7 8 9
Commands
Pause Time Setting (Automatic closure)
Activation of Always Close function.
Force/Speed
Adjust maximum operator speed during opening cycle
Adjust maximum operator speed during closing cycle
Adjust deceleration speed during opening cycle
Adjust deceleration speed during closing cycle
Start Operator 1 deceleration during opening cycle
Start Operator 1 deceleration during closing cycle
Adjust pedestrian opening
Enable/Disable Operator Brake
Enable/Disable Soft Stop
Enable/Disable Soft Start
LED strip control
Remote controls
Read saved codes and set function
Assign a text string for each code
Delete single code
Add a new code
Check the presence of a code
Photocells
Activation/Deactivation of Partial Inversion on Close
10
(0"..40 min)
(10%..100%)
(10%..100%)
(10%..100%)
(10%..100%)
( 0%..100%)
( 0%..100%)
(10%..100%)