DeWalt DE6210 Bedienungsanleitung Seite 29

Fig. A1
1 Base
2 Dovetailing template
3 Locking lever for front vice
4 Front vice
5 Adjustment knobs for front vice
6 Template position securing knobs
7 Template position adjustment knobs
8 Depth guide
9 Offset guides
10 Adjustment knobs for top vice
11 Top vice
12 Locking lever for top vice
13 Mounting holes
14 Template fi ngers
Supplied accessories (fi g. A2)
The following accessories are supplied with the attachment:
15 Dovetail cutter type A
16 Straight cutter type B (DE6212)
17 Guide bush and lock nut type A
18 Guide bush and lock nut type B (DE6212)
19 Guide bush adaptor plate for DW613/DW614/DW615
20 Guide bush adaptor plate for DW620/DW621/DW626
21 Guide bush adaptor plate for DW624/DW625E/DW629
Optional accessories
The cutters supplied with the attachment have to be fi tted in an 8 mm
collet assembly. The following collet assemblies are available:
- DE6951 collet assembly (for DW613/DW614/DW615/DW620/
DW621)
- DE6273 collet assembly (for DW624/DW625E/DW629)
- DE6261 collet assembly (for DW626)
Consult your dealer for further information on the appropriate
accessories.
Assembly and adjustment
+
Also refer to your router manual.
Preparing the dovetailing attachment (fi g. A & B)
● Mount the dovetailing attachment to a workbench with screws of a
suitable size. For this purpose, the base has mounting holes (13).
Make sure that the front edge of the base of the attachment projects
beyond the workbench.
● Alternatively, mount the dovetailing attachment temporarily on a
workbench. Use clamps (26) to mount the dovetailing attachment to
the workbench as shown in fi g. B.
@
Always secure the attachment to a stable surface.
Preparing the router (fi g. C)
In order to accommodate your D
attachment, a guide bush adaptor plate assembly has to be fi tted to the
router base. Other brands of routers may require a separate sub-base
to be used.
@
We recommend to use a router with integrated fi ne adjuster
for the depth of cut, or to fi t your router with a suitable fi ne
adjuster.
● Fit the adaptor plate (27) to the router base.
● Insert the guide bush (28) into the adaptor plate as shown.
WALT router for use with the
E
● Secure the guide bush to the adaptor plate using the lock nut (29).
● Insert the required cutter into the collet.
● Adjust the cutter as described below.
@
Always use the guide bushes supplied with the attachment
to guide the router against the template fi ngers. To select the
proper guide bush for a given joint, place the guide bush in
the depth setting slot on the left side of the corresponding
template. The guide should have a snug fi t in the slot.
Adjusting the cutter depth (fi g. D1 & D2)
The depth guides on the templates are factory pre-set for the standard
joints, but can be adjusted as necessary.
● Lower the cutter just past the edge of the guide bush.
● Slide the router with the guide bush into the depth setting slot that
corresponds with the joint to be routed. This is always the slot to the
left of the template fi ngers being used.
30 TAILS/BOX
31 HALF-BLIND
32 PINS
33 1/2" DADO
34 3/8" DADO
35 1/4" DADO
● Lower the router carriage until the cutter contacts the depth guide
(8). Lock the router carriage in this position.
Marking and clamping the workpieces (fi g. E - G)
Your dovetailing attachment is capable of making a number of joints
including:
- Through dovetails (fi g. E1)
- Half-blind dovetails (fi g. E2)
- Rebated half-blind dovetails (fi g. F1)
- Sliding dovetails (fi g. F2)
● Carefully mark the mating parts of the project as shown in fi g. E - F.
● Loosen the left offset guide (9) using the T-handle Allen key (36).
Slide the guide to the far left position.
● Position the horizontal workpiece (37) and clamp it into place using
the top vice (11) (fi g. G1). Make sure that the edge of the workpiece
does not project beyond the edge of the attachment.
● Insert the lugs of the template (2) between the adjustment knobs (7)
and securing knobs (6). Hold the template down with one hand while
tightening the securing knobs with the other.
● Position the vertical workpiece (38) centred between the farthest
fi nger on the left and the nearest fi nger on the right of the template
(fi g. G2). Make sure that the edge of the workpiece is fl ush with the
bottom of the template. Clamp the workpiece into place using the
front vice (4).
● Slide the left offset guide (9) to the right until it is fl ush against the
vertical workpiece. Fasten the offset guide using the T-handle Allen
key (36).
● Loosen the top vice. Move the horizontal workpiece (37) until it is
fl ush against the vertical workpiece (38) and the left offset guide (9)
(fi g. G3). Tighten the top vice.
@
● Fit a piece of scrap material (39) of the same thickness as
the workpiece to keep the vice even and the templates fl at
(fi g. G3).
● Clamp a piece of scrap material tightly against the workpiece
to minimise break-out from the cutter.
Mounting and adjusting the template (fi g. H1 - H3)
The templates can be used on both sides to enable routing of different
joints (fi g. H1).
E N G L I S H
for dovetails and box joints
for half-blind dovetails
for dovetail pins
for sliding dovetails (12.7 mm, fi xed)
for sliding dovetails (9.5 mm, fi xed)
for sliding dovetails (6.35 mm, fi xed)
29