Package Contents; Residual Risks; Electrical Safety - DeWalt D27107 Bedienungsanleitung

EnGLIsH
• Use only saw blades specified by the manufacturer. Ensure that the riving knife is not thicker
than the width of the groove cut by the saw blade and not thinner than the body of the
saw blade.
• Make sure the machine is placed on an even surface with sufficient stability.
• Do not use abrasive or diamond disc.
• In case of an accident or machine failure immediately switch the machine off and disconnect
from power source.
– Report the failure and mark the machine in suitable form to prevent other people from
using the defective machine.
• When the saw blade is blocked due to abnormal feed force during cutting, turn the machine
off and disconnect it from power supply. Remove the workpiece and ensure that the saw blade
runs free. Turn the machine on and start new cutting operation with reduced feed force.
• Refrain from removing any cut-offs or other parts of the workpiece from the cutting area while
the machine is running and the saw head is not in the rest position
• Do not use the machine without the legs mounted.
• Make sure your position is always left or right of the cutting line.
• Provide adequate general or localized lighting.
• Ensure the operator is adequately trained in the use, adjustment and operation of
the machine.
• Switch the machine off when unattended.
• Make sure that the LED meets EN 62471. Do not replace the LED with a different type. If
damaged, have the LED light repaired by an authorized service agent.
• Connect the saw to a dust collection device when sawing wood. Always consider factors
which influence exposure of dust such as:
– type of material to be machined (chip board produces more dust than wood);
– sharpness of the saw blade;
– correct adjustment of the saw blade,
– dust extractor with air velocity not less than 20 m/s.
– Ensure that the local extraction as well as hoods, baffles and chutes are properly adjusted.
• Never cut light alloy, especially magnesium.

WARNING: We recommend the use of a residual current device with a residual current
rating of 30mA or less.

Residual Risks

The following risks are inherent to the use of saws:
• injuries caused by touching the rotating parts.
In spite of the application of the relevant safety regulations and the implementation of safety
devices, certain residual risks cannot be avoided. These are:
• Impairment of hearing;
• Risk of accidents caused by the uncovered parts of the rotating saw blade;
• Risk of injury when changing the blade;
• Risk of squeezing fingers when opening the guards;
• Health hazards caused by breathing dust developed when sawing wood, especially oak, beech
and MDF.
The following factors are of influence to noise production:
• The material to be cut;
• The type of saw blade;
• The feed force.
The following factors increase the risk of breathing problems:
• No dust extractor connected when sawing wood;
• Insufficient dust extraction caused by uncleaned exhaust filters
• Worn saw blade;
• Workpiece not exactly guided.

Electrical Safety

The electric motor has been designed for one voltage only. Always check that the power
supply corresponds to the voltage on the rating plate.
Your D WALT tool is double insulated in accordance with EN61029; therefore no
e
earth wire is required.
If the supply cord is damaged, it must be replaced only by D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 13 A.
30
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension cable suitable for the
power input of this tool (see Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Partly assembled machine
•
•
Markings on Tool
The following pictograms are shown on the tool:
Date Code Position (Fig. A1)
The date code
Example:
Description (Fig. A1–A7)

WALT or an authorised
e
a1
1
2
3
4
5
6
7
8
9
10
11
12
1 Box containing:
1 Top guard for bench saw position
1 Under-table guard for mitre saw position
4 Legs
2 Wheels
4 Feet
1 Parallel fence
1 Material clamp
1 Instruction manual
Check for damage to the tool, parts or accessories which may have occurred during transport.
Take the time to thoroughly read and understand this manual prior to operation.
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Carrying Point
Hands Away
Visible radiation. Do not stare into light. (D27107XPS)
When using the machine in the mitre saw mode, make sure to
operate the trigger switch in the handle when switching ON
O / I
and OFF. Do not operate the switchbox in this mode. The on/off
switch located on the machine frame is foreseen for table saw
mode only.
When using the machine in the mitre saw mode, make sure the
riving knife is secured in its rest position.
Never use as mitre saw when the guard is not in place.
, which also includes the year of manufacture, is printed into the housing.
12
2020 XX XX
Year of Manufacture
WARNING: Never modify the power tool or any part of it. Damage or personal injury
could result.
On/off switch (saw bench mode)
Table release lever
Rotating table clamp
Mitre saw table
Rotating table
Fence right-hand side
Fence left-hand side
Moveable lower blade guard
Guard release lever
Operating handle (Fig. A2)
Circuit breaker reset button
Date code
2 ; the