English (Original Instructions); Safety Instructions - DeWalt D27107 Bedienungsanleitung

EnGLIsH
FLIP-OVER SAW
D27107, D27107XPS
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough product development and
e
innovation make D WALT one of the most reliable partners for professional power tool users.
e
Technical Data
Voltage
Type
Power input
Power output
Max. blade speed
Blade diameter
Blade bore
Blade body thickness
Riving knife thickness
Automatic blade brake time
Weight
Cutting capacities
Mitre saw mode
Mitre (max. positions)
Bevel (max. positions)
Max. crosscut capacity at 90°/90°
Max. mitre cut capacity at 45°
Max. depth of cut 90°
Max. depth of bevel cut 45°
Max. depth of cut at 45° bevel, 45° mitre
saw bench mode
Max. ripping capacity left/right
Depth of cut at 90°
Depth of cut at 45°
Noise values and/or vibration values (triax vector sum) according to EN61029:
L (emission sound pressure level)
PA
L (sound power level)
WA
K (uncertainty for the given sound level)
Vibration emission value a =
h
Uncertainty K =
The vibration and/or noise emission level given in this information sheet has been measured in
accordance with a standardised test given in EN61029 and may be used to compare one tool
with another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration and/or noise emission level represents the main
applications of the tool. However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration and/or noise emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and/or noise should also take
into account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator from the effects of vibration
and/or noise such as: maintain the tool and the accessories, keep the hands warm
(relevant for vibration), organisation of work patterns.
nOTE: This device is intended for the connection to a power supply system with maximum
permissible system impedance Zmax of 0.28 Ω at the interface point (power service box) of
user's supply.
The user has to ensure that this device is connected only to a power system which fulfils the
requirement above. If necessary, the user can ask the public power supply company for the
system impedance at the interface point.
28
D27107 D27107XPS
V 230 230
AC
7 5
(D27107
withworklight LED)
W 2000 2000
W 1080 1080
-1 4000 4000
min
mm 305 305
mm 30 30
mm 2.1–2.2 2.1–2.2
mm 2.5 2.5
s < 10 < 10
kg 42 42
left 48° 48°
right 48° 48°
left 48° 48°
right 2° 2°
mm 205 x 63 205 x 63
mm 160 160
mm 90 90
mm 60 60
mm 60 60
mm 120/320 120/320
mm 80 80
mm 56 56
dB(A) 95,0 95.0
dB(A) 106.0 106.0
dB(A) 3.0 3.0
m/s 2 2.1 2.1
m/s 2 1.5 1.5
EC-Declaration of Conformity
Machinery Directive
FLIP-OVER SAW
D27107/D27107XPS
WALT declares that these products described under Technical Data are in compliance with:
D
e
2006/42/EC, EN61029-1:2009 +A.11:2010, EN61029-2-11:2012 +A11:2013.
These products also comply with Directive 2014/30/EU and 2011/65/EU. For more information,
please contact D WALT at the following address or refer to the back of the manual.
e
The undersigned is responsible for compilation of the technical file and makes this declaration
on behalf of D WALT.
e
Markus Rompel
Vice President of Engineering, PTE-Europe
D WALT, Richard-Klinger-Straße 11,
e
D-65510, Idstein, Germany
19.06.2017
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may
result in property damage.

Denotes risk of electric shock.

Denotes risk of fire.

Safety Instructions

WARNING! When using electric tools basic safety precautions should always
be followed to reduce the risk of fire, electric shock and personal injury including
the following.
Read all these instructions before attempting to operate this product and save these instructions.
SAVE THIS MANUAL FOR FUTURE REFERENCE
General Safety Rules
1 . Keep work area clear.
– Cluttered areas and benches invite injuries.
2 . Consider work area environment.
– Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the
work area well lit (250300 Lux). Do not use the tool where there is a risk of causing fire or
explosion, e.g., in the presence of flammable liquids and gases.
3 . Work floor area.
– DO NOT use the stand on uneven surfaces. The stand is designed to be used on a flat,
stable surface. If the saw stand can slide around or wobbles, the power tool or the
workpiece cannot be evenly and securely guided.
4 . Guard against electric shock.
– Avoid body contact with earthed surfaces (e.g., pipes, radiators, cookers and refrigerators).
When using the tool under extreme conditions (e.g., high humidity, when metal swarf is
being produced, etc.), electric safety can be improved by inserting an isolating transformer
or a (FI) earth-leakage circuit-breaker.
5 . Keep other persons away.
– Do not let persons, especially children, not involved in the work, touch the tool or the
extension cord and keep them away from the work area.
6 . Store idle tools.
– When not in use, tools must be stored in a dry place and locked up securely, out of reach
of children.
7 . Do not force the tool.
– It will do the job better and safer at the rate to which it was intended.
8 . Use the right tool.
– Do not force small tools to do the job of a heavy duty tool. Do not use tools for purposes
not intended; for example do not use circular saws to cut tree limbs or logs.