DeWalt D27107 Bedienungsanleitung Seite 37


WARNING: Certain dust, such as oak or beech dust, is considered carcinogenic, especially
in connection with wood-treatment additives.
• Always use dust extraction.
• Provide for good ventilation of the work space.
• It is recommended to wear an appropriate respirator.
Connect a dust collection device designed in accordance with the relevant regulations. The air
velocity of externally connected systems shall be 20 m/s ±2 m/s. Velocity to be measured in
the connection tube at the point of connection, with the tool connected but not running.
connecting Mitre saw Position (Fig. T1)
1. Connect the one end of the first hose to the dust extraction adaptor
2. Insert the other end of the hose into the middle inlet port of the manifold
3. Connect the one end of the other hose to the under-table guard
4. Insert the other end of the hose into the outer inlet port of the manifold.
connectingsaw Bench Position (Fig. T2)
• Proceed as for mitre saw position, only connect the hose from the under-table guard to
the saw blade guard 23 .
Mitre Saw Extra Support/Length Stop (Fig. A4)
The extra support and length stop can be mounted on the left-hand side or on the right-hand
side, or with two sets on either side.
1. Fit the items 29 – 31 onto the two guide rails
2. Use the inclinable support 29 for cross-cutting 210 mm wide boards (15 mm thick).
Side Extension Table (Fig. A5)
The side extension table increases the distance from the rip fence to the blade to 600 mm
33
or more, depending on the rod length fitted to the machine and the clamped position of the
table. The side extension table must be used in conjunction with guide rails
adjustable table is equipped with an engraved scale along its front edge and mounted on a
sturdy base which clamps to the guide rods.
• Fit the extension table to the right-hand side of the machine for continuity of the distance
scale on both tables.
Sliding Table (Fig. A6)
This sliding table 34 allows for board sizes to the left of the blade up to 1200 x 900 mm.
The guide rods are mounted on a sturdy alloy extrusion which is quickly detachable from the
machine and yet fully adjustable is all planes.
The fence incorporates a full length measuring tape for quick positioning of an adjustable stop
and an adjustable support for narrow workpieces.
Transporting (Fig. U)

WARNING: Always transport the machine in saw bench mode with the upper blade
guard fitted.
The castor wheels provide an easier transport of the machine.
1. Put the machine on the right base side.
2. Fold the rear legs into the base
3. Fold the front legs out of the base
4. Turn the machine straight up.
5. Lift the machine by the front legs up to the wheels are in contact with the floor.

WARNING: When carrying the machine, always seek assistance.
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period of time with a
e
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care
and regular cleaning.

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. An accidental start-up can cause injury.
Lubrication
The bearings of the motor are pre-lubricated and watertight.
• Slightly oil the rotating table bearing surface where it slides on the lip of the fixed table at
regular intervals.
• Periodically lubricate the depth of cut screwthread.
• Clean the parts subject to accumulation of sawdust and chips periodically with a
dry brush.
Cam Adjustment (Fig. V1–V3)
To take out the clearance between the two tables, proceed as follows:
1. Rotate the machine into saw bench mode.
2. Remove the screws 100 and the retainer plate
3. Loosen the screw 102 of the adjustment cam
4. Rotate the adjustment cam using a pair of needle nose pliers.
5. Hold the adjustment cam with the pliers and tighten the screw.
6. Replace the retainer plate and tighten the screws.
15 .
99 .
51 .
27 & 28 .
27 (option). The
101 .
103 .
7. Rotate the machine into mitre saw mode. Check the force that is needed to mitre the saw.
Repeat the above steps if the force needed is too high.
Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.

WARNING: To reduce the risk of injury, regularly clean the table top.

WARNING: To reduce the risk of injury, regularly clean the dust collection system.
Optional Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Saw Blades
ALWAYS USE 305 mm SAW BLADES WITH 30 mm ARBOUR HOLES. SPEED RATING MUST BE
AT LEAST 4000/min. Never use a smaller or greater diameter blade. It will not be guarded
properly. Use crosscut blades only! Do not use blades designed for ripping, combination
blades or blades with hook angles in excess of 10°.
BLADE DESCRIPTIONS
application
construction saw Blades (for all purpose cutting)
General Purpose
Woodworking saw Blades (provide smooth, clean cuts)
Fine crosscuts
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked with this symbol must not be
disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing
the demand for raw materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at www.2helpU.com.
EnGLIsH
WALT, have not been tested
e
Diameter (mm) Teeth
305 36
305 60
35