Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Note the markings in the middle of the blades and the squeegee!
The markings on the squeegee and the blades must agree.
• Push the blades back into the slots, and then firmly retighten the clamp at
the bottom with the allen screws.
Malfunctions
Malfunction
Possible causes
Machine does
Maschine switched off
not run
Discharged batteries
Battery/mains
unit malfunction
(display on cont-
rol panel)
Batteries/battery char-
ger defective
Immobiliser
Machine does
not move
Main fuse defect
Power cord not
plugged in or defective
Batteries not
sufficiently char-
ged
Traction block batteries
or battery charger de-
fective
Brush unit switched off • Press brush unit button
Tools do not ro-
tate
Motor runs but not tool
Check the seal on the
tank lid for cracks/dirt
Squeegee not on the
floor
Poor vacuum
performance
Suction hoses not
plugged in
Floor remains
wet
Vacuum air filter blo-
cked
Soiled solution
not picked up
Worn blades
Hose or nozzle blocked
(e.g. by pieces of wood
or residual material)
Vacuum swit-
Recovery tank full
ched off
Flex tank empty
Insufficient out-
flow of cleaning
Cleaning solution
solution
quantity too low
36
Troubleshooting
page
• Switch the machine on
(Keyswitch to Start po-
31
sition)
• Move the machine by
pushing the manual
brake release (the but-
ton must be held
31
down)
• Recharge batteries
• Move the machine by
pushing the manual
brake release (the but-
ton must be held
31
down)
• Call for technical assis-
tence
• Stand on the running
31
board
• Move the machine by
pushing the manual
brake release (the but-
ton must be held
31
down)
• Call for technical assis-
tence
• Plug in the power cord
• Call for technical assis-
tence
• Move the machine by
pushing the manual
brake release (the but-
ton must be held
31
down)
• Call for technical assis-
tence
31
• Call for technical assis-
tence
• Clean the seal, or re-
place if defective
31
• Press the vacuum but-
31
ton
• Plug both suction ho-
33
ses into squeegee
• Remove the blockage
31
• Change/turn the
35
blades
• Remove the blockage
• Empty the recovery
34
tank
• Fill the Flex tank
34
• Set up the cleaning so-
31
lution quantity with +/-
Error indications in the display
Malfunction
Possible causes
SAFE
Internal fault
E020
Discharged batteries
Unevenness of the
E041
floor or failure of a
brush motor
Drive error running
E048
drive, brush unit, suc-
tion unit.
Communication data
E051
bus
Transport
• Interrupt the battery - machine connection with the Emergency Stop button.
Refer to Page 37 for the dimensions and weights.
Caution:
This machine may only be lifted ot transported with the use of an
aid, such as a ramp or a lifting platform!
Transport the machine in an upright position and disconnect/remove the
batteries for transportation.
Make sure that the machine is securely fastened within the transportation
vehicle and is secured against tipping over.
Disposal
When it has reached the end of its operational life, the machine and its
accessories must be disposed of according to the national regulations. Your
TASKI partner can support you with proper disposal upon notification.
Batteries
The batteries must be removed from the machine before being disposed of
properly.
Used batteries must be disposed of in an environmentally appropriate way
according to the EU guidelines 91/157/EEC
Troubleshooting
page
• Switch the machine
OFF/ON again (keys-
witch at the Start posi-
tion)
• Call for technical as-
sistence
• Move the machine by
pushing the manual
brake release (the but-
ton must be held
31
down)
• Recharge batteries
• Switch the machine
OFF/ON again (keys-
witch at the Start posi-
tion)
• Call for technical as-
sistance
• Switch the machine
OFF/ON again (keys-
witch at the Start posi-
tion)
• Move the machine by
pushing the manual
brake release (the but-
ton must be held
down)
• Call for technical as-
sistance
• Call for technical as-
sistance
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
