Before Starting The Equipment; Assembling The Equipment - Parkside PMTS 210 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

7. Before starting the equipment

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
m WARNING
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The equipment must be securely installed, i.e. bolted down
on a workbench, base frame or similar. Use the holes on the
inner side of the frame legs for this.
• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you press the On/Off switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply make
sure the data on the rating plate are identical to the mains
data.
• Connect the equipment to a properly installed protective
contact socket, with at least 16 A circuit breaker.

8. Assembling the equipment

m WARNING: Disconnect the mains power plug before
maintaining, resetting or assembling the table saw.
8.1 Before assembling the equipment
• Place all parts supplied on a flat surface.
• Group equal parts.
NOTE:
• If compounds with a bolt (round head / or hexagon), hex
nuts and washers are backed up, the washer must be fitted
under the nut.
• Insert screws each from outside to inside. Secure connections
with nuts on the inside.
• Tighten the nuts and bolts during assembly only to the extent
that they can not fall down. If you tighten the nuts and bolts
prior to final assembly, final assembly can not be performed.
8.2 Fitting the table width extension (fig. 4-6)
1. Loosen the knurled screws (26) (fig. 5).
ATTENTION: Do not unscrew the knurled screws (26) too
far.
2. Feed the guide tubes (23) of the table width extension (22)
into the guide bushings (27) (see fig. 4/5).
3. Slide the end pieces (24) into the guide tubes (23) of the
table width extension (22) as shown in fig. 6.
4. Fasten the end pieces (24) with the screws (25) as shown
in Fig. 6.
5. Pull the table width extension (22) out completely and fas-
ten in place with the knurled screws (26) (Fig. 5).
6. Now fold out the support feet (30).
7. Align the table width extension (22) horizontally with the
table saw.
8. Loosen the lock nuts (29) on the respective support foot
(30) and adjust the height adjustment screw (28) as re-
quired.
9. Then retighten the lock nuts (29).
If you do not need the table width extension (22), fold the sup-
port feet (30) in.
8.3 Fitting/removing the
(fig. 7)
1. Place the saw blade guard (4) together with the screw (4a)
on the riving knife (3) from above, so that the screw sits
firmly in the hole of the riving knife (31).
2. Do not over-tighten the screw (4a). The saw blade guard
(4) must remain free to move.
3. Disassembly takes place in reverse order.
m WARNING: Before starting sawing, the saw blade
guard (4) must be lowered onto the material to be sawn.
After fitting, check that the saw blade guard (4) is function-
ing properly. Lift the saw blade guard and then release it. The
saw blade guard should automatically move back to its starting
position.
8.4 Removing/fitting the table inlay (fig. 8)
m WARNING: In the event of wear or damage the table
insert (6) must be replaced; otherwise there is an increased
danger of injury.
1. Move the saw blade into the bottom position (see 9.2).
2. Take off the saw blade guard (4).
3. Remove the table insert screws (32).
4. Remove the table insert (6).
5. Installation of the table insert (6) takes place in reverse
order.
8.5 Setting the riving knife (fig. 9)
m WARNING: Pull out the mains plug.
m WARNING: The setting of the saw blade (5) must be
checked after every saw blade replacement.
1. Set the saw blade (5) to the max. cutting depth, move to
the 0° position and lock in place (see 9.2).
2. Remove the saw blade guard (4) (see 8.3).
3. Remove the table inlay (6) (see 8.4).
4. Loosen the fastening screws (33)
5. Align the riving knife (3) such that
a) the distance between the saw blade (5) and the splitter
(3) is max. 5 mm (fig. 10) and
b) the saw blade (5) is parallel to the splitter (3).
6. Retighten the fastening screws (33) and fit the table insert
(6) (see 8.4).
7. Fit the saw blade guard (4) again (see 8.3).
saw blade guard
GB 25