Handle Starter Assembly (Illustration D + L1 ); Attaching The Grass Collector To The Mower (Illustration R1 + S1 ); Adjusting The Cutting Height (Illustration I ); Fitting The Cable Harness (Only For Electro-Start) - Sabo 54-A ECONOMY Betriebsanleitung

Handle starter assembly (Illustration D + L1 )

– The safety control bracket (1) on the upper handle (2) must be folded down before the starter cable can be suspended.
– Pull out the starter cable (3) slowly and fit in the starter handle mount (4) with a twist motion.

Attaching the grass collector to the mower (Illustration R1 + S1 )

– First insert the grass bag frame with the clip forward into the grass bag. Please make sure that the protective corners of
the collection material cover the back corners of the collecting bag frame. Align the upper seams of the bag with the clip.
– Press the retaining profiles of the collecting sack onto the bars of the collecting sack frame R1 .
– Open the ejection flap of the mower upwards.
– Pick up the collecting sack by the carrying strap, place the chute (1) R1 at the collecting sack opening into the ejection
flap and hang it in the mower casing with its two side hooks upwards S1 .
– Attach ejection flap to collector.

Adjusting the cutting height (Illustration I )

– The cutting height is set on the left hand side of the lawnmower
– Press the button with your thumb (1) and move the handle of the lawnmower into the required position by moving it up
or down (2).
– By letting go of the button, the lever locks into the required cutting height.
– The marking on the left of the housing indicates the cutting height.
IMPORTANT
Mowing at the lowest cutting height should only be carried out on level and plane lawns!
Please note that the lower cutting height settings may only be used for optimum conditions. If you select cutting
height that is too low, the turf may be damaged and under certain circumstances even destroyed.
Besides the cutting height, the driving speed also influences the cutting pattern and collection result. Adapt the
cutting height and driving speed to the grass height to be cut, the motor drive may not need to be switched on.

Fitting the cable harness (only for electro-start)

Fix the pre-assembled cable harness to the right lower handle using the enclosed longer cable clips in such a way that the
plug can be fitted to the contacts of the starter lock without tension.

Fitting the charged starter battery (only for electro-start) (Figure J3 + V1 + U1 )

– Removers the screw (1) (TORX T30) behind the motor, and remove the battery cover (2) J3 .
– Place the battery on the battery retainer behind the engine, making sure that the connecting cable is pointing to the right
V1 .
– Thread the two clips of the battery cover into the battery retainer grooves and carefully close the cover with the (TORX
T30) screw, at the same time feeding out the cable through the groove in the cover.
Connect the battery plug with the counter-plug of the cable form before mowing U1 .
–
To charge the battery, see section "Charging the starter battery".

8 BEFORE USING THE LAWNMOWER FOR THE FIRST TIME

Check that all connections and the spark plug connector are fitted firmly. Tighten the screws if necessary! In particular make
sure that the cutter bar is fitted correctly (see Chapter "Maintenance of the blade").
The blade attachment screw should always be fitted and tightened by a specialist workshop. If the blade attachment screw is
too tight or too loose, the blade clutch and blade can be damaged or become detached, which can cause severe injury.
Make sure that all safety devices are fitted properly and are not damaged.

Charging the starter battery (only for electro-start)

– The starter battery is a maintenance-free dry battery
– Prior to the initial start-up, it should be charged with the original charger for approx. 24 hours.
For safety reasons and to avoid battery damage, the battery may only be charged within a building in dry rooms
and not in direct sunlight.
– To avoid unnecessary power consumption, disconnect the power plug from the charger after charging and disconnect
the battery from the charger.
See table for explanation of symbols page 3
See table for explanation of symbols page 3
9
Safety instruction!
GB
Safety instruction!