Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
IMPORTANT REMARKS
For any installation problems please contact V2
TEL. (+39) 01 72 81 24 11
V2 has the right to modify the product without previous
notice; it also declines any responsibility to damage or injury
to people or things caused by improper use or wrong
installation.
Please read this instruction manual very carefully before
installing and programming your PD11 control unit.
• This instruction manual is only for qualified technicians,
who specialize in installations and automations.
• The contents of this instruction manual do not concern the
end user.
• Every programming and/or every maintenance service
should be done only by qualified technicians.
AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE
WITH THE EUROPEAN REGULATIONS IN FORCE:
EN 60204-1 (Machinery safety. electrical equipment of
machines, part 1: general rules)
EN 12445
(Safe use of automated locking devices,
test methods)
EN 12453
(Safe use of automated locking devices,
requirements)
• The installer must provide for a device (es. magnetotermical
switch) ensuring the omnipolar sectioning of the equipment
from the power supply.
The standards require a separation of the contacts
of at least 3 mm in each pole (EN 60335-1).
• After making connections on the terminal board, use one
hose clamp to fix dangerous voltage wires near the terminal
board and another hose clamp to fix safety low voltage wires
used for accessories connection; this way, in case of
accidental detachment of a conducting wire, dangerous
voltage parts will not come into contact with safety low
voltage ones.
• The plastic case has an IP55 insulation; to connect flexible
or rigid pipes, use pipefittings having the same insulation
level.
• Installation requires mechanical and electrical skills,
therefore it shall be carried out by qualified personnel only,
who can issue the Compliance Certificate concerning the
whole installation (EEC Machine Directive 89/392, Annex IIA).
• The automated vehicular gates shall comply with the
following rules: EN 12453, EN 12445, EN 12978 as well
as any local rule in force.
• Also the automation upstream electric system shall comply
with the laws and rules in force and be carried out
workmanlike.
• The door thrust force adjustment shall be measured
by means of a proper tool and adjusted according to
the max. limits, which EN 12453 allows.
• We recommend to make use of an emergency
button, to be installed by the automation (connected
to the control unit STOP input) so that the door may
be immediately stopped in case of danger.
• Always remember to connect the earth according to
current standards (EN 60335-1, EN 60204-1).
DECLARATION DE CONFORMITÉ
V2 ELETTRONICA SPA déclare que les opérateurs de la série
VEGA-C sont conformes aux qualités requises par les
Directives:
73/23/EEC sécurité électrique
93/68/EEC compatibilité electromagnétique
99/05/EEC directive radio
98/37/EEC directive machines
Nota: Déclare que n'est pas permis mettre en service les
dispositifs indiqués ci-dessous jusqu'à quand la machine
(porte automatisé) soie été identifiée, marqué CE et on aie
émise la conformité aux conditions de la Directive
89/392/EEC et ses modifications.
Le responsable de la mise en service doit fournir les papiers
suivants:
• Dossier technique
• Déclaration de conformité
• Marque CE
• Verbal de vérification
• Registre de l' entretien
• Notices de montages et avertissements
Racconigi le 18/10/2006
Le représentant dument habilité V2 ELETTRONICA SPA
A. Livio Costamagna
DONNEE TECHNIQUES
Alimentation
Puissance nominal
Absorption
Puissance absorbée
Courant max. moteur
Condensateur
Vitesse moyenne
Température de fonctionnement
Degré de protection
Cycle de fonctionnement
Poids moteur
Charge max accessoires 24V
Fusible de protection
37
VEGA230V-C
VEGA120V-C
230VAC - 50Hz 120VAC - 60Hz
280 W
280 W
2,5 A
4,5 A
575 W
575 W
2,5 A
4,5 A
8 µF
30 µF
1,6 Rpm
1,9 Rpm
-20 ÷ +50 °C
-20 ÷ +50 °C
IP20
IP20
30 %
30 %
9 Kg
9 Kg
3W
3W
5A
8A
Werbung
Inhaltsverzeichnis
