Special Accessories; Electrical Connection; Fitting The Appliance - Gaggenau VP 414 110 Montageanleitung

Special accessories

You can order the following special accessories from your
specialist dealer:
VA 440 010 Stainless steel appliance cover
VA 420 000 Connection strip for combination with other
Vario 400 appliances for flush installation
VA 420 001 Connection strip for combination with other
Vario 400 appliances for flush installation
with appliance cover/extension
VA 420 010 Connection strip for combination with other
Vario 400 appliances for surface installation
VA 420 011 Connection strip for combination with other
Vario 400 appliances for surface installation
with appliance cover/extension
VA 450 400 Appliance extension, 38 cm
Only use the accessories as specified. The manufacturer
accepts no liability if these accessories are used incorrectly.
Preparing the cabinet (Fig. 1a)
The kitchen unit must be heat-resistant to at least 90°C (about
190°F). The stability of the unit must be maintained after
producing the cut-out.
Produce the cut-out in the worktop for one or more Vario
appliances as shown in the installation sketch. The angle
between the cut surface and the worktop must be 90°.
The cut edges at the sides must be flat to ensure a good fit of
the retaining springs on the appliance. In laminated worktops, it
may be necessary to fit strips at the sides of the cut-out.
Remove shavings after cutting. Seal cut surfaces for resistance
to heat and so they are watertight.
Pay attention to a minimum gap of 10 mm from the underside of
the appliance to kitchen units.
Use suitable base constructions to ensure load-carrying
capacity and stability, especially in the case of thin worktops.
Pay attention to the weight of the appliance, including any
payload. Reinforcement material used must be resistant to heat
and moisture.
Note: Wait until the appliance has been installed in the
installation opening before checking that it is level.
Flush installation (Figure 1b)
Flush installation in a worktop is possible.
The appliance can be installed in the following temperature-
resistant and waterproof worktops:
Stone worktops
■
Worktops made of plastics (e.g. Corian
■
Solid wood worktops: Only by arrangement the with worktop
■
manufacturer (seal recess edges)
For other materials, coordinate with the worktop manufacturer
■
with regard to use.
Installation in laminated wood worktops is not possible.
Note: All recessing work on the worktop must be performed in a
specialist workshop on the basis of the installation sketch. The
recess must be produced neatly and precisely because the cut
edge is visible on the surface. Clean and degrease the recess
edges with a suitable cleaning agent (observe the silicone
manufacturer's processing notes).
Fitting several Vario appliances (Fig. 1c)
You can order the connecting strip VA 420 000/001/010/011
as a special accessory to combine several Vario appliances.
Allow for the additional space required for the connecting strip
when producing the cut-out (see installation instructions
VA 420 000/001/010/011).
Appliances can also be fitted in individual recesses, if a
minimum ridge width of 50 mm between the recesses is
observed.
To enable combination of appliances with and without an
appliance cover, dimension differences can be balanced out by
the extension VA 450 110/-400/-600/-800/-900 (depending on
appliance width).
Combination with the appliance cover (Fig. 1d)
You can order the appliance cover VA 440 010 as a special
accessory. Allow for the additional space required for the
appliance cover when producing the cut-out.
)
®
Boring to fit the control knobs (Fig. 2a + 2b)
The control console can be integrated in the base cupboard at
the drawer level. Thickness of cabinet front: 16 - 26 mm
As shown in the installation sketch, drill the Ø 35 mm holes to
1.
secure the control knobs in the cabinet front. Attach the
enclosed stencil to the cabinet front for correct positioning of
the bore.
If the cabinet front is thicker than 26 mm, the front must be
2.
routed from the back to max. 26 mm on an area of
80 x 310 mm.

Electrical connection

Check the electrical installation system before connecting the
appliance. Make sure that the household installation has
sufficient fuse or circuit breaker protection. Check that the
appliance has the same voltage and frequency as the electrical
installation system (see rating plate).
The appliance corresponds to protection class I and may only
be operated with a protective earth connection.
The installation system must incorporate an all-pole isolating
switch with a contact gap of at least 3 mm. This must remain
accessible after installation.
Only a qualified electrician who takes the appropriate
regulations into account may connect or replace the mains
connection cable.
Appliance without mains connection cable: Only connect as
shown on the connection diagram. Mains connection cable:
Typ H05 VV-F (3x1,5 mm²) or higher rated. The yellow/green
wire for the PE connection must be 10 mm longer than the other
wires on the appliance side.
Do not kink or trap the mains connection cable.
Installing the control panel (Fig. 3 + 4)
Note: Only install appliance with the control panel of the
corresponding type.
Remove all packaging from the control knob and peel off the
1.
protective film behind the luminous disc.
Open the lid of the connecting terminal on the control panel.
2.
Secure the mains connecting lead as shown in the connection
diagram. Secure the connecting lead with the pull relief. Close
the lid of the connecting terminal.
Hold the support plate from the rear against the cabinet front,
3.
insert control knobs into the holes, secure from the rear with
the nuts. Take care to install control knobs in the correct order
(see figure).
Secure the control panel with the included nuts onto the
4.
support plate.

Fitting the appliance

Firmly plug in the connecting cable between the appliance and
1.
the control console (the plugs must lock into place). Plug the
control cable into the socket on the appliance. The plug must
lock into place (Fig. 5).
Lower the appliance evenly into the cut-out and press down
2.
firmly (Fig. 6a).
Note: The appliance should fit tightly in the cut-out without
moving around (e.g. during cleaning). If the cut-out width is on
or above tolerance limit it may be necessary to fit filler strips to
the sides of the cut-out.
Connect the appliance to the electricity. Test that it functions
3.
correctly. If the luminous discs behind both control knobs blink
alternately, check the connecting cable between the appliance
and the control console is firmly plugged in.
4. Only for flush fitting (Fig. 6b): Check appliance for correct
functioning before applying sealant! Fill the surrounding gap
between the work surface and the frame with a suitable, heat-
resistant silicone adhesive (e.g. OTTOSEAL
the sealing joint using the smoothing agent recommended by
the silicone manufacturer. Check the usage information for the
silicone adhesive. Do not use the appliance until the silicone
adhesive has completely dried (at least 24 hours depending
on room temperature).
Caution!
Unsuitable silicone adhesives can cause permanent
discolouration on work surfaces made from natural stone.
S 70). Smooth
®