Instructions For Installation; General Instructions - Baron 700 Serie Aufstellung, Gebrauchs- Und Instandhaltungs Anweisungen

Data Emissione 24/06/2003

1 - INSTRUCTIONS FOR INSTALLATION

1.1 Identifying the models
Gas solid top - Top
Gas solid top + 2 gas burners Sx - Top
Gas solid top + 2 gas burners Dx - Top
Gas solid top + 4 gas burners - Top
Gas solid top on gas oven
Gas solid top + 2 gas burners on gas oven
Gas solid top + 4 gas burners on gas oven
Gas solid top on open cabinet
Gas solid top + 2 gas burners Sx on open cabinet
Gas solid top + 2 gas burners Dx on open cabinet
Gas solid top + 4 gas burners on open cabinet
1.2 Technical data
The technical data of these solid tops are indicated in the Tables
T4, T5 and T6 (refer to the Enclosures).

2 - GENERAL INSTRUCTIONS

Read the instructions of this handbook carefully because they
supply important information on installation, use and maintenance
safety. Keep this handbook carefully for any further reference of the
various operators. The installation, transformation and maintenance
of this equipment must exclusively be carried out by qualified
installers or by proper companies complying with the safety rules in
force.
The Manufacturer declines any liability if these rules are not
complied with.
2.1 Installation
After unpacking, check that the equipment is intact. In case of any
doubt, do not operate this apparatus and call immediately a
professional engineer. Arrange the packing elements far from
children, because they can be dangerous. The equipment must
definitively be installed in the position it occupies in the kitchen,
preferably under an exhausting hood for a proper recirculation of air.
The equipment must be installed only in rooms with a good
ventilation. Any equipment of the type A1 and B21 must be
installed only in rooms with a good ventilation, according to the
technical rules in force. An optimum position may be under an
exhausting hood that intakes combustion gases and vapours. The
installation of any equipment of the type B11 must be carried out
in such a way that exhaust gases are sent to a proper system
constructed according to the standards in force. The connection
stack is supplied separately. Specify the type of installation crossing
the proper square: A1 - B11 - B21, of the rating plate (included in
the control board). These solid tops can be installed separately, or
assembled with other equipment of our line. This equipment is not
available in built-in version. The equipment must be positioned at
least 10 cm far from any wall surrounding it. In case of fire-proofing,
or thermally insulated walls, this distance can also be reduced.
The overall dimensions of the equipment are indicated in the
following pages.
2.2 Installing the connection stack (fig. 6)
Remove the grates of flue-gas exhaust from the stack of the
equipment. Remove the film protecting the adhesive strips of the 2
threaded plates "B" and make them adhere in the stack "A", as it is
shown in the fig. 6. The holes must coincide. Remove the back of
the stack "C". Position the stack "C" on the stack "A"; fasten them
with the screws "D". Apply the back of the stack "C" again.
SERIES 700
803152141
803152461S
803152461D
803152681
803132141
803132461
803132681
803112141
803112461S
803112461D
803112681
2.3 Installation under exhausting hood (fig. 7)
When installing the equipment under an exhausting hood, mount the
connection stack (without draft switch) at such a height that the
distance between the stack end and the filter of the hood must be
included between 125 and 200 mm. This result can be obtained
through the following operations (fig. 7). Install the stack as it has
been explained at the point 2.2. Insert the moving element of the
stack in its end, then shift it until the desired height (between 125
and 200 mm) is reached. Fix this "telescopic" section drilling 4 holes
in the reference points marked on the sides of the moving element,
then fasten with the proper self-tapping screws.
2.4 Installing the draft switch (fig. 8)
When required by the rules in force, the draft switch (supplied
separately) must be applied as follows:
install the stack following the instructions of the point 2.2. Apply the
draft switch to the stack. Fasten it with the 4 self-tapping screws.
Insert the exhaust pipe of proper diameter, for the connection to the
outside, in the sleeve of the draft switch.
2.5 Assembling
Remove the protection film from the outer surfaces of the apparatus.
Clean these surfaces from probable residual adhesive using a
proper solvent. Level the apparatus turning the proper adjustable
feet. As regards the assembling of the stack extension (when
necessary), refer to the point 2.2. As regards the assembling of the
draft switch (when necessary), refer to the point 2.4.
2.6 Assembling the top on a neutral base (fig. 3)
Assemble the top on the proper neutral base through the following
operations:
Remove knobs, control board and back of the top. Position the top
on its base. Fasten these two elements with the four screws V, as
shown in the fig. 3. Reassemble the control board and the back of
the top.
2.7 Aligning the equipment (fig. 2)
Operate as follows:
Remove the knobs and the control board of the top. Arrange the
apparatuses side by side and level at the same height. Fasten the
apparatuses with the proper screws, as shown in the fig. 2.
2.8 Assembling the tops in bridge configuration (fig. 3/A)
Fix the two supporting crossbars T in the proper holes drilled in the
sides of the contiguous bases. Level the two bases carefully.
Position the top on the crossbars and remove the knobs and the
control board from this top. Fasten the top onto the crossbars with
the four screws V, as shown in the fig. 3. Align and fix the
13
Revisione 0.0
SERIES 900
803162141
803162461S
803162461D
803162681
803142141
803142461
803142681
803122141
803122461S
803122461D
803122681