Use And Maintenance - Baron 700 Serie Aufstellung, Gebrauchs- Und Instandhaltungs Anweisungen

Data Emissione 24/06/2003
Solid top -Piezoelectric lighter, ignition plug or pilot burner cable
faulty.
5.2 Extinction of pilot burner during the operation of solid top and
open burners
The thermocouple is faulty, or it is not properly heated, or not
correctly connected to the gas cock. Gas feeding pressure drop.
The gas cock is faulty.
5.3 The main burners of solid top & open burners show a difficult
ignition or they fail to ignite
Insufficient gas feeding pressure. Nozzles clogged. The gas cock is
faulty.
5.4 The pilot burner of the gas oven shows a difficult ignition or it
fails to ignite
Piezoelectric lighter, ignition plug or pilot burner cable faulty.
Insufficient gas feeding pressure. Nozzle or pipe clogged. The gas
valve is faulty.
5.5 Extinction of pilot burner during the operation of the oven
The thermocouple is faulty, or it is not properly heated, or not
correctly connected to the gas cock. Gas feeding pressure drop.
The gas valve is faulty.
5.6 The main burner of the gas oven shows a difficult ignition or it
fails to ignite
Insufficient gas feeding pressure. Nozzles clogged. The gas valve is
faulty.
5.7 Difficult control of oven temperature
The gas valve is faulty.
6 - REPLACING SOME COMPONENTS
N.B.: The sealed components must not be tampered with. After
any operation, check that there are no leaks, if necessary.
6.1 Main burner of the solid top
Remove the knobs and the control board, then remove the griddle
plate. Unscrew the gas pipe reaching the nozzle support.
Unloose the three screws fixing the main burner to the top, from
above. Extract the burner from the top.
REASSEMBLE THE COMPONENT CARRYING OUT THE SAME
OPERATIONS BACKWARDS.
6.2 Thermocouple, pilot burner of the solid top
Remove the knobs and the control board, then remove the griddle
plate. Replace the component.
6.3 Gas valve, piezoelectric lighter of the gas oven
Remove the vertical control board of the oven and, if necessary, the
right side of the equipment, then replace the component.
6.4 Thermocouple of gas oven
Remove the vertical control board and the lower horizontal panel of
the oven, then replace the component.
6.5 Pilot burner, ignition plug of the gas oven
Remove the lower horizontal panel and the bottom panel of the
oven, then replace the component.
6.6 Main burner of the gas oven
Remove the lower horizontal panel and the bottom panel of the
oven, then replace the component.
6.7 Main burner of the cook top (open burners)
Remove the knobs and the control board, besides the grates, the
fire caps and burner heads. Unscrew the gas pipe reaching the
nozzle support. Unscrew the two screws fixing the pilot burner to the
body of the main burner, from above. Unscrew the 3 screws
fastening the burner to the cook top. Extract the burner from the
front of the equipment.
REASSEMBLE THE COMPONENT CARRYING OUT THE SAME
OPERATIONS BACKWARDS.
6.8 Thermocouple and pilot burner of the cook top (open burners)
Remove the knobs and the control board, besides the grates, the
fire caps and burner heads. Replace the component.
6.9 Gas cock of solid top and open burners
Remove knobs and control board. Replace the component.

7 - USE AND MAINTENANCE

7.1 Warning
This equipment has been designed for professional aims, therefore
it must be operated exclusively by trained personnel.
It must exclusively be used to cook food; consequently any other
use is improper. Its installation and possible transformation for other
gas group must be carried out by authorized and qualified installers.
In case of troubles, turn off the gas cutoff cock installed before the
equipment. For any repair, call the authorized After-Sales Service
and require only original spare parts.
Not complying with these instructions may seriously
compromise the safety of this equipment; the manufacturer
declines any liability in case these warnings are not complied
with.
7.2 Use of solid top and open burners
The knob controlling the cocks is marked with the following symbols:
Off
Pilot burner on
Maximum fire
Minimum fire
7.3 Lighting the burners of solid top and open burners
Press and turn the knob to the position
pressing the button of the piezoelectric lighter (only in the solid top,
the pilot flame of open burners is lit manually, for instance, with a
match). After lighting, keep the knob pressed for approximately 20
seconds, then release it. In case of extinction of the pilot burner,
repeat this operation. The pilot burner can be checked through the
sight glass of the control board. In emergency cases, light the pilot
burner manually approaching a flame and keeping the knob in the
position
.
Turn the knob to the desired position chosen between
15
Revisione 0.0
. Light the pilot burner
and