Instructions For Installation; General Instructions - Baron 700 serie Aufstellung, Gebrauchs- Und Instandhaltungs Anweisungen

Data Emissione 09/09/2003

1 - INSTRUCTIONS FOR INSTALLATION

1.1 Identifying the models
4 burners with gas oven
6 burners with gas oven
8 burners with gas oven
2 burners with open base
4 burners with open base
6 burners with open base
8 burners with open base
Gas cook top-Top with 2 burners
Gas cook top-Top with 4 burners
Gas cook top-Top with 6 burners
Gas cook top-Top with 8 burners
1.2 Technical data
The technical data of these apparatuses are indicated in the
Tables T5 - T5A - T6 - T6A

2 - GENERAL INSTRUCTIONS

Read the instructions of this handbook carefully because they
supply important information on installation, use and
maintenance safety. Keep this handbook carefully for any further
reference of the various
transformation and maintenance of this equipment must
exclusively be carried out by qualified installers or by proper
companies complying with the safety rules in force.
The Manufacturer declines any liability if these rules are not
complied with.
N.B. - This equipment complies with the CEI standard 61-50.
2.1 Installation
- After unpacking, check that the equipment is intact. In case of
any doubt, do not operate this apparatus and call immediately
a professional engineer.
- Arrange the packing elements far from children, because they
can be dangerous.
- The equipment must definitively be installed in the position it
occupies in the kitchen, preferably under an exhausting hood
for a proper recirculation of air.
- The equipment must be installed only in rooms with a good
ventilation.
- Any equipment of the type A1 must be installed only in
rooms with a good ventilation, according to the technical rules
in force.
An optimum position may be under an exhausting hood that
intakes combustion gases and vapors.
- Specify the type of installation crossing the proper square: A1 -
B11 - B21, of the rating plate (included in the control board).
- These ranges can be installed separately, or assembled with
other equipment of our line.
- This range is not available in built-in version.
- The equipment must be positioned at least 10 cm far from any
wall surroundung it. In case of fire-proofing, or thermally
insulated walls, this distance can also be reduced.
- The overall dimensions of the equipment are indicated in the
following pages.
SERIE 700
Models with
manual ignition
of fires
803131141
803131161
803131181
803111121
803111141
803111161
803111181
803151121
803151141
803151161
803151181
operators. The installation,
Models with Models with
electric ignition manual ignition
of fires
803131341
803131361
803131381
803111321
803111341
803111361
803111381
803151321
803151341
803151361
803151381
2.2 Assembling
- Remove the protection film from the outer surfaces of the
apparatus. Clean these surfaces from probable residual
adhesive using a proper solvent.
- Level the apparatus turning the proper adjustable feet.
- In stand-alone version, the range has a width of 40 cm and it
must be fixed to the floor with the proper flanges (Fig. 2A).
2.3 Assembling the cook top on a neutral base (Fig. 3)
- Assemble the cook top on the proper neutral base through the
following operations:
- Remove knobs, control board and back of the top.
- Position the top on its base.
- Fasten these two elements with the four screws V, as shown in
the fig. 3.
- Reassemble the control board and the back of the top.
2.4 Aligning the equipment (Fig. 2)
Operate as follows:
- Remove the knobs and the control board of the top.
- Arrange the apparatuses side by side and level at the same
height.
- Fasten the apparatuses with the proper screws,as shown in the
fig.2
2.5 Assembling the tops in bridge configuration (Fig. 3A)
- Fix the two supporting crossbars T in the proper holes drilled in
the sides of the contiguous bases.
- Level the two bases carefully.
- Position the cook top on the crossbars and remove the knobs
and the control board from this top.
- Fasten the top onto the crossbars with the four screws V, as
shown in the fig. 3.
- Align and fix the apparatuses arranged side by side, as
indicated above (paragraph 2.4 - Fig. 2).
- Reassemble the back, the control board and the knobs of the
top.
2.6 Connection to the gas pipe network
- Before connecting the equipment, consult the gas service
company.
- Insert a cutoff cock before the apparatus, in an easily
accessible position.
- Make sure that there are no leaks in pipe unions.
14
SERIE 900
Models with
electric ignition
of fires
803141141 803141341
803141161 803141361
803141181 803141381
803121121 803121321
803121141 803121341
803121161 803121361
803121181 803121381
803161121 803161321
803161141 803161341
803161161 803161361
803161181 803161381
Revisione 0.0
of fires