Alarms - Minipack-Torre Pratika 56CS Installations-, Gebrauchs- Und Wartungsanleitung

Chapter 6. Machine adjustment and setting up

6.3. Alarms

The machine includes a series of ALARMS that are necessary in order monitor hazard and
fault conditions.
Whenever an alarm is activated, the display views the fault, together with an acoustic signal
and the red light element turns on (E2),
When the alarm is restored, the red light element and acoustic signal turn off.
ALARM
ALARM
STOP PRESSED
ALARM
DOOR OPEN
ALARM
IO [....]
ALARM
MICRO ON BAR
ALARM
THERMIC MOTOR
ALARM
INVERTER
ALARM
TOO FULL
ALARM
SEALING BAR RISE
ALARM
BAR DESCENT
ALARM
PHOTOCELLS
ALARM
BELT RETURN
ALARM
POSITION
ALARM
SIDE RAMPE
ALARM
FRONT RAMPE
ALARM
SIDE ADJUST.
ALARM
FRONT ADJUST.
ALARM
SIDE PROBE
ALARM
FRONT PROBE
The machine is fitted with "EMERGENCY" Pushbutton (S0) that stop the machine instantaneously when
pressed, interrupting the work cycle.
To reset this alarm, proceed as follows:
Remove the cause of the alarm. Release the "EMERGENCY" Pushbutton (S0) by rotating it to the right.
Press the RESET (S1) button
CAUSE
The emergency button has been pressed (S0).
A door or the upper hood is open.
Comunication lack between electronic card and
power boards (CAN-BUS).
Parcel remained under sealing bar.
One micro is out of its place or out of order.
Sensor on cylinder is out of its place or out of order.
Not active.
Inverter block (check on the inverter display the
cause).
Waste film winder roll, too full.
The sealing bar doesn't open.
Upper bar sensor is out of order.
Compressed air lack or solenoid valve is faulty.
The sealing bar doesn't open.
Upper bar sensor is out of order.
Compressed air lack or solenoid valve is faulty.
The photocells are darkened beyond the max.
configuration time, or not aligned or our of order.
Mobil conveyor is not drew back.
Compressed air lack.
Sensor our of order.
Inconsistency between sensor signals.
Side sealing bar heating time fault.
Front sealing bar heating time fault.
Side sealing bar does not remain at temperature
set.
Front sealing bar does not remain at temperature
set.
One sealing bars heater is not heating up.
Thermocouple out of place.
One sealing bars heater is not heating up.
Thermocouple out of place.
Release the EMERGENCY button (S0)
by turning it to the right.
Press the RESET button (S1).
Close the door or the upper hood.
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
Remove the alarm cause.
Press button (16).
Press button (13).
35
GB
RESET