Maintenance - Stiga PARK POWER Gebrauchsanweisung

Never use high-pressure water. This can
damage shaft seals, electrical compo-
nents or hydraulic valves.
Never use high-pressure air against the
radiator fins. This will damage the fin
structure.
Clean the machine after each use. The following
instructions apply for cleaning:
• Do not spray water directly at the engine.
• Clean the engine with a brush and/or com-
pressed air.
• Clean the engine's cooling air intake (12:W).
• After cleaning with water, start the machine and
any cutting deck to remove the water that may
otherwise penetrate bearings and cause

5 MAINTENANCE

5.1 SERVICE PROGRAMME
In order to keep the machine in good condition as
regards reliability and operational safety as well as
from an environmental perspective, STIGA's Serv-
ice programme should be followed.
The contents of this programme can be found in
the attached service log.
Basic service must always be carried out by an au-
thorised workshop.
First service and intermediate service should be
carried out by an authorised workshop, but can
also be carried out by the user. The content of this
can be found in the service log and the actions are
described under "4 STARTING AND OPERA-
TION" as well as below.
Servicing carried out at an authorised workshop
guarantees professional work using genuine spare
parts.
At each basic service and intermediate service car-
ried out at an authorised workshop, the service log
is stamped. A service log presenting these services
is a valuable document that improves the ma-
chine's second-hand value.
5.2 PREPARATION
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable(s) from the spark plug(s) and re-
moving the ignition key.
ENGLISH
5.3 TYRE PRESSURE
Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).
5.4 CHANGING ENGINE OIL
This section contains tables covering the different
engines that are included in STIGA's range. To fa-
cilitate reading, mark the data that applies to the
relevant machine/engine.
5.4.1 Change intervals
The table below states hours of operation and cal-
endar months. Carry out the relevant action at
whichever occurs first.
damage.
Changing the oil
Replacing the filter.
Change the oil more frequently if the engine has to
operate in demanding conditions or if the ambient
temperature is high.
5.4.2 Engine Oil
Use oil according to the table below.
Oil
Service class
Use oil without any additives.
Do not fill with too much oil. This can cause the
engine to overheat.
Change oil when the engine is warm.
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. Therefore allow the engine to
cool a few minutes before draining the
oil.
1. Attach the clamp on the oil drainage hose. Use
a polygrip or similar. See fig. 12:Y.
2. Move the clamp up 3-4 cm on the oil drainage
hose and pull out the plug.
3. Collect the oil in a collection vessel.
NOTE! Do not spill any oil on the drive belts.
4. Hand in the oil for disposal in accordance with
local provisions.
5. Install the oil drainage plug and move the clamp
back so that it clamps above the plug.
6. Remove the dipstick and fill with new oil.
Oil quantity:
No filter replacement
7. After filling up the oil, start the engine and idle
for 30 seconds.
1st time Then at inter-
5 hours
-
SAE 10W-30
SJ or higher
Oil quantity, approximately
Filter replacement
1.6 litres
EN
vals of
50 hours/
12 months
100 hours
1.7 litres
57