Elektro-Automatik PSI 9000 3U Betriebsanleitung Seite 91

TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty .........................................................5
1.3 Limitation of liability ........................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical Data ...............................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ...................................9
1.8.3 Specific technical data .................................10
1.8.4 Views ............................................................18
1.9 Construction and function ............................22
1.9.1 General description ......................................22
1.9.2 Block diagram ..............................................22
1.9.3 Scope of delivery .........................................23
1.9.4 Accessories ..................................................23
1.9.5 Options .........................................................23
1.9.6 The control panel (HMI) ...............................24
1.9.7 USB port type B (rear side) .........................27
1.9.8 Interface module slot ...................................27
1.9.9 Analog interface ...........................................27
1.9.10 "Share" connector ........................................28
1.9.11 "Sense" connector (remote sensing) ...........28
1.9.12 Master-Slave bus .........................................28
1.9.13 GPIB port (optional) .....................................28
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage .................................29
2.1.1 Transport ......................................................29
2.1.2 Packaging ....................................................29
2.1.3 Storage .........................................................29
2.2 Unpacking and visual check ........................29
2.3 Installation ....................................................29
2.3.1 Safety procedures before installation and
use ................................................................29
2.3.2 Preparation ...................................................30
2.3.3 Installing the device .....................................30
2.3.4 Connection to AC supply .............................31
2.3.5 Connection to DC loads ...............................32
2.3.6 Grounding of the DC output ........................33
2.3.7 Connecting the "Share" bus ........................33
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
2.3.8
2.3.9
2.3.10 Connecting the analog interface .................35
2.3.11
2.3.12 Initial commission .........................................35
2.3.13 Commission after a firmware update or a
3
OPERATION AND APPLICATION
3.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.6
3.6.1
3.6.2
3.7
3.8
3.9
3.9.1
3.9.2
3.9.3
3.9.4
3.9.5
3.9.6
3.9.7
3.9.8
3.9.9
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
PSI 9000 3U Series
Connection of remote sense .......................33
Installation of an AnyBus interface module .34
Connecting the USB port (rear side) ...........35
long period of non-use .................................35
Personal safety ............................................36
Operating modes .........................................36
Voltage regulation / Constant voltage .........36
Current regulation / constant current / current
limiting ..........................................................36
Power regulation / constant power / power
limiting ..........................................................37
Internal resistance regulation ......................37
Alarm conditions ..........................................38
Power Fail ...................................................38
Overtemperature ..........................................38
Overvoltage protection.................................38
Overcurrent protection .................................38
Overpower protection ..................................38
Manual operation .........................................39
Switching on the device ...............................39
Switching off the device ...............................39
Configuration via MENU ..............................39
Adjustment limits ..........................................47
Changing the operating mode .....................47
Manual adjustment of set values .................48
Switching the DC output on or off ................49
Remote control .............................................50
General .........................................................50
Control locations ..........................................50
Remote control via a digital interface ..........50
Remote control via the analog interface
(AI) ................................................................51
Alarms and monitoring .................................55
Definition of terms ........................................55
Device alarm and event handling ................55
Control panel (HMI) lock ..............................57
Loading and saving a user profile ...............57
The function generator.................................58
Introduction...................................................58
General .........................................................58
Method of operation .....................................59
Manual operation .........................................59
Sine wave function .......................................60
Triangular function .......................................61
Rectangular function ....................................61
Trapezoidal function .....................................62
DIN 40839 function ......................................62
www.elektroautomatik.de
ea1974@elektroautomatik.de
Page 3