Dmx Operation - EuroLite LED KLS--170 Bedienungsanleitung

Battery
The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery
contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil
from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not
possible.
If the range of the remote control decreases, replace the battery. For this purpose, on the
rear side of the remote control press the small bar with the groove to the right and at the
same time remove the battery support. For operation, one 3 V button cell type CR 2025 is
required. When inserting, pay attention that the positive pole of the button cell shows
upwards in the support.

DMX operation

Setting the Number of DMX Channels and the DMX Starting address
For operation with a controller with DMX512 protocol, the light set is equipped with 25 control channels. However,
it can also be switched to a mode with 3 or 6 channels if different functions are required. To be able to operate the
light set with a DMX controller, the DMX starting address must be set for the first DMX channel. The starting
address depends upon which DMX controller is being used. Please refer to the controller's documentation.
1 Press the button MENU so many times until dПH is indicated in the display. Confirm with the ENTER button.
The display indicates the DMX start address.
2 Confirm with ENTER. The display indicates 3CH (3 DMX channels), 6CH (6 DMX channels) or 25CH (25 DMX
channels). Use the ▲ and ▼ buttons to select the desired number of DMX channels.
3 Confirm with ENTER. Now the display indicates the menu item for the DMX start address d***. Confirm with
ENTER, then use ▲ and ▼ to set the address.
4 Confirm ENTER. A dot will flash when DMX signals are being received. If no control signals are available, the
DMX address set will be flashing.
Functions in DMX mode
3-channel mode
Channel Value
Blackout, automatic mode and sound-controlled mode
000‒009 Blackout
010‒050 Automatic mode spots
051‒090 Automatic mode strobe LEDs
1
091‒130 Automatic mode spots and strobe LEDs
131‒170 Sound control spots
171‒210 Sound control strobe LEDs
211‒255 Sound control spots and strobe LEDs
Program selection for automatic mode and sound-controlled mode
000‒255 Automatic mode spots
000‒255 Automatic mode strobe LEDs
2 000‒255 Automatic mode spots and strobe LEDs
000‒255 Sound control spots
000‒255 Sound control strobe LEDs
000‒255 Sound control spots and strobe LEDs
Automatic mode spots
Channel 1: 010‒050
000‒014 AP01 show program 1
015‒029 AP02 show program 2
030‒044 AP03 show program 3
045‒059 AP04 show program 4
060‒074 AP05 show program 5
075‒089 AP06 show program 6
090‒104 AP07 show program 7
105‒119 AP08 show program 8
120‒134 AP09 show program 9
135‒149 AP10 show program 10
150‒164 AP11 show program 11
165‒179 AP12 show program 12
180‒194 AP13 show program 13
195‒209 AP14 show program 14
210‒224 AP15 show program 15
225‒239 AP16 show program 16
240‒255 AP17 show program 17
Automatic mode strobe LEDs
Channel 1: 051‒090
000‒024 AF01 show program 1
025‒049 AF02 show program 2
050‒074 AF03 show program 3
075‒099 AF04 show program 4
100‒124 AF05 show program 5
125‒149 AF06 show program 6
150‒174 AF07 show program 7
175‒199 AF08 show program 8
200‒224 AF09 show program 9
225‒249 AF10 show program 10
250‒255 AF11 show program 11
28 • EN
Function
Automatic mode spots, strobe LEDs
Channel 1: 091‒130
000‒099
100‒199
200‒255
AM01 show program 1
AM02 show program 2
AM03 show program 3