Operating Determinations - EuroLite LED KLS--170 Bedienungsanleitung

The compact light set LED KLS-170 consists of four
slimline LED spots and strobe LEDs with control unit.
The set comes pre-assembled in a practical
transport bag. It can be placed on a lighting stand or
mounted to a truss. Control is possible via wireless
foot switch or IR remote control.
• This device is designed for professional use in the
field of event technology, e.g. on stage. It is not
suitable as household lighting.
• This product is only allowed to be operated with an
alternating voltage of 100-240 V, 50/60 Hz and was
designed for indoor use only. The occupation of
the connection cables is as follows:
Cable Pin
Brown Live
Blue Neutral
Yellow/Green Earth
The earth has to be connected! If the device will be
directly connected with the local power supply
network, a disconnection switch with a minimum
opening of 3 mm at every pole has to be included
in the permanent electrical installation. The device
must only be connected with an electric installation
carried out in compliance with the IEC standards.
The electric installation must be equipped with a
Residual Current Device (RCD) with a maximum
fault current of 30 mA.
• Lighting effects are not designed for permanent
operation. Consistent operation breaks will ensure
that the device will serve you for a long time
without defects.
• Do not shake the device. Avoid brute force when
installing or operating the device. When choosing
the installation spot, please make sure that the
device is not exposed to extreme heat, moisture or
dust. There should not be any cables lying around.
You endanger your own and the safety of others!
• This device must never be operated or stockpiled
in surroundings where splash water, rain, moisture
or fog may harm the device. Moisture or very high
humidity can reduce the insulation and lead to
mortal electrical shocks. When using smoke
machines, make sure that the device is never
exposed to the direct smoke jet and is installed in a
distance of 0.5 meters between smoke machine
and device. The room must only be saturated with
an amount of smoke that the visibility will always be
more than 10 meters.
• This product was designed for indoor use only.
The ambient temperature must always be between
-5° C and +45° C. Keep away from direct insulation
and heaters. The relative humidity must not exceed
50 % with an ambient temperature of 45° C. This
device must only be operated in an altitude
between -20 and 2000 m over NN. Never use the
device during thunderstorms. Over voltage could

OPERATING DETERMINATIONS

International
L
N
destroy the device. Always disconnect the device
during thunderstorms.
• Make sure that the installation complies with the
standards and rules that apply in your country. The
device must be installed securely and prevented
from falling down. Always secure it with an
appropriate safety bond.
• The symbol
distance from lighted objects. The minimum
distance between light output and the illuminated
surface must be more than 0.1 meters. Make sure
there is no highly inflammable material within a
distance of min. 0.5 meters (danger of fire!).
• In order to safeguard sufficient ventilation, leave
50 cm of free space around the device. The
housing must never touch surrounding surfaces or
objects.
• Make sure that the area below the installation place
is blocked when rigging, derigging or servicing the
fixture.
• Do not look directly at the light source! Persons
with light-sensitive epilepsy may suffer from
epileptic seizures or fall unconscious.
• Operate the device only after having become
familiarized with its functions. Do not permit
operation by persons not qualified for operating the
device. Most damages are the result of
unprofessional operation!
• Please consider that unauthorized modifications on
the device are forbidden due to safety reasons!
• Never remove the serial barcode from the device
as this would make the guarantee void.
• If this device will be operated in any way different to
the one described in this manual, the product may
suffer damages and the guarantee becomes void.
Furthermore, any other operation may lead to
dangers like short-circuit, burns, electric shock,
crash etc.
• Never remove the serial barcode from the device
as this would make the guarantee void.
21 • EN
determines the minimum
- - -m