Operation Without External Control; Interconnecting Several Light Sets (Master/Slave Operation) - EuroLite LED KLS--170 Bedienungsanleitung

Operation without external control

Automatic mode
In automatic mode, various show programs are available that run at an adjustable speed.
1 Press the MENU button so many times until Aut for automatic mode is indicated in the display. Confirm with
the ENTER button.
2 Use the ▲ and ▼ buttons to select the desired program mode: AutP = spots, AutF = strobe LEDs or AutM for
a combination of all devices. Confirm with ENTER.
3 Use ▲ and ▼ to select the number of the desired program. Confirm with ENTER. The display indicates menu
item running speed.
4 Use ▲ and ▼ to adjust the running speed of the program from S.01 (slow) to S.99 (fast). Confirm with ENTER.
Sound control
Via the microphone, which is integrated in the control unit, the light set can perfectly reproduce the show
programs to the rhythm of the music (sufficient bass provided).
1 Press the MENU button so many times until Sou for sound control is indicated in the display. Confirm with the
ENTER button.
2 Use the ▲ and ▼ buttons to select the desired program mode: SouP = spots, SouF = strobe LEDs or SouM
for a combination of all devices. Confirm with ENTER.
3 Use ▲ and ▼ to select the number of the desired program. Confirm with ENTER.
4 Adjust the microphone sensitivity to the volume of the music with the SENSITIVITY control. The LEDs do no
light if the volume is too low or if there is no sufficient bass beat.
Individual color settings
In the color mode CoLo the white and UV strobe LEDs light and the spots light constantly in red, green and blue. It
is possible to adjust the flash frequency of the strobe LEDs and the brightness of the spots.
1 Press the button MENU so many times until CoL is indicated in the display. Confirm with the ENTER button.
The display indicates CoLo.
1 Press ENTER. Now the display indicates the letter R for the color and the corresponding brightness value.
2 Use the ▲ and ▼ buttons to adjust the desired brightness.
3 Confirm with ENTER. Now the color green can be adjusted; then blue.
4 The stetting of the strobe LEDs is the final menu item. Use ▲ and ▼ to select the number of the desired flash
frequency from S.01 (slow) to S.99 (fast).

Interconnecting several light sets (master/slave operation)

Several light sets may be interconnected (max. 32). Then all slave units can be synchronized and controlled with
the master unit without the need for a DMX controller. The units must be set to the corresponding operating
modes.
Slave units
Configure all slave units before connecting the master unit.
1 Press the MENU button so many times until SLA is indicated in the display. Confirm with the ENTER button.
The slave address is indicated.
2 Slave units must be addressed in ascending order (first unit = 1, second unit = 2, etc.). Confirm with ENTER,
then use the▲ and ▼ buttons to set the address. Confirm with ENTER.
3 The display will continue to flash until control signals are being received from the master unit.
4 Connect the DMX output of the master unit to the DMX input of the first slave unit. Then connect the DMX
output of the first slave unit to the DMX input of the second slave unit, etc. until all units have been connected
in a chain. Make sure the master unit is the first in the chain. Do not connect a DMX controller to the DMX input
of the master unit.
Master unit
1 Press the MENU button so many times until SYS is indicated in the display. Confirm with the ENTER button.
2 Call menu item M-En with the ▲ and ▼ buttons. Confirm with ENTER.
3 Use ▲ and ▼ to select the setting ON. Thus, the unit is set to master.
4 Select the desired show program (automatic mode or sound-controlled mode). The interconnected light sets
will now operate in sync.
26 • EN