Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Programming
4.3 Time and Date Menu Item
4.3.1 General.
The Time and Date menu item
sets the Recorder's internal clock for time and date
dependent features such as recording to disk, alarm
annotation, and rec documentation. The time is pro-
grammed and displayed in a 24-hour format. The
date is programmed and displayed in a user pro-
grammable American or European format. It is rec-
ommended that you set the time and date upon
system start-up. Time & date are stored in the bat-
tery backed up real time clock. If the time and date
are not set or are lost, it defaults to midnight
(00:00:00) on January 01, 1995 (01/01/95).
Changing the Time or Date will reset all re-
settable point types.
0 4 /1 6 /9 7
0
0 4 /1 6 /9 7
SP C
0 4 /1 6 /9 7
1 0 3 7 31 M A
Figure 4-4 Accessing Program Menu Flow Chart
4.3.2 How to Program Time and
Date.
The following steps detail how to set Time
and Date on the Recorder. Also refer to Figure 4-5,
Time and Date Setup Flow Chart, for details.
1. At the Display Button Bar, press the MENU
Button.
2. At the Command Button Bar, press the PRO-
Gram Button.
4-6
NOTE
4 :5 9 :2 9
7
8
4
5
1
2
4 :5 9 :2 9
4 :5 9 :2 9
3. Use the UP (↑) or DOWN (↓) Arrow Keys, on
the Button Bar, to scroll to and highlight "Time &
Date" and press the ENTER Button.
A. Changing Time
time such as "12:30:25".
1. Press ENTER or YES to accept current Time
and skip to Date or NO to program a new time. If
NO is pressed, continue with steps 2 through 4.
The display will pop up a dialog box to set the
hour.
2. To program Hours, use the keypad on the pop-
up dialog box, to enter the correct hour number
(23 is max.) and press ENTER in the lower left-
hand corner of the screen.
3. To program Minutes, use the keypad on the
pop-up dialog box, to enter the correct minute
number (max. is 59) and press ENTER in the
lower left-hand corner of the screen.
4. To program Seconds, use the keypad on the
pop-up dialog box, to enter the correct seconds
number (max. is 59) and press ENTER in the
lower left-hand corner of the screen. The screen
will then show a pop-up dialog box showing the
current date programmed into the Recorder.
9
B. Changing Date -
6
similar to this example: "01/01/95".
3
1. Press ENTER or YES to accept current Date or
NO to program new Date. Press EXIT to leave the
dialog box without making any changes.
2. To program the month, use the keypad on the
pop-up dialog box, to enter the correct month
number (12 is maximum) and press ENTER in the
lower left-hand corner of the screen.
3. To program the day, use the keypad on the
pop-up dialog box, to enter the correct day num-
ber (31 is maximum) and press ENTER in the
lower left-hand corner of the screen.
4. To program the year, use the keypad on the
pop-up dialog box, to enter the correct year num-
ber (no maximum) and press ENTER in the lower
left-hand corner of the screen. The display will
return to the Program Menu bar. Press EXIT twice
to return to the display menu bar.
Refer to Paragraph 4.4.4 to change the Date For-
mat.
- The display will show the
The date will be displayed
Siemens AG C79000-G7374-C211-01
SIREC D Manual
Werbung
Kapitel
Inhaltsverzeichnis
