Unauthorised Modification And Manufacture Of Spare Parts; Improper Use; Transport And Interim Storage; Intended Use - Wilo -Drain TM 32 Einbau- Und Betriebsanleitung

English
2.6 Unauthorised modification and manufacture of
spare parts
Modifications to the product are only permissible
after consultation with the manufacturer. Original
spare parts and accessories authorised by the
manufacturer ensure safety. The use of other
parts can nullify the liability from the results of
their usage.

2.7 Improper use

The operational safety of the supplied product is
only guaranteed for conventional use in accord-
ance with section 4 of the installation and operat-
ing instructions. The limit values must on no
account fall under or exceed those specified in the
catalogue/data sheet.

3 Transport and interim storage

As soon as the product arrives:
• Check the product for damage in transit,
• In the case of transport damage, initiate the nec-
essary procedures with the forwarding agent
within the time stipulated.
CAUTION! Danger of property damage!
Incorrect transport and incorrect intermediate
storage can lead to product damage.
• The pump may only be suspended/carried by the
strap provided for transport purposes. The cable
should never be used for lifting!
• The pump must be protected against moisture,
frost and mechanical damage when transported
and stored.

4 Intended use

The Drain TM series drainage and submersible
waste water pumps are used:
• for the automatic drainage of pits and shafts,
• for keeping dry yard areas and basement rooms
exposed to flooding,
• for lowering surface water,
if the waste water is not able to flow off into the
sewer system through natural fall.
The pumps are suitable for pumping slightly con-
taminated water, rainwater, drainage water and
washing water.
TMR pumps versions are intended for pumping
down to 2 mm suction level from the floor. This
version is recommended for mobile installation
and pumping clear water.
5.2

Technical data

Mains voltage:
Mains frequency:
Protection class:
Insulation class:
Speed:
Max. current consumption:
Power consumption P
Max. flow rate:
Max. delivery head:
Operating mode S1:
10
1~230 V, ± 10 %
50 Hz
IP 68
155
2900 rpm (50 Hz)
See name plate
: See name plate
1
See name plate
See name plate
200 operating hours a year
The pumps are usually installed under water (sub-
merged) and can only be permanently or trans-
portably installed vertically. Because of the sheath
current cooling, the pumps can also be operated
unsubmerged.
Submersible pumps with a mains connection cable
of less than 10 metres are (according to EN 60335)
only permitted for use inside buildings, i.e. not for
operating outside.
Pumps that are intended for use in or at garden
ponds or similar places must have a mains con-
necting cable that is not lighter than rubber
sheathed cables reference H07 RN-F (245 IEC 66)
according to EN 60335.
Danger! Mortal danger due to electric shock
The pump many not be used to drain swimming
pools / garden ponds or similar places if anyone
is in the water.
WARNING! Hazardous to health!
Owing to the materials used, the pumps are not
suitable for potable water! Unpurified foul and
waste water represents a health hazard.
CAUTION! Danger of property damage!
Pumping unpermitted substances can lead to
product damage.
The pumps are not suitable for water with
coarse contamination such as sand, fibres or
combustible, caustic fluids or for use in poten-
tially explosive areas.
Correct use of the product also includes following
these instructions.
Any use over and beyond these is interpreted as
incorrect use.

5 Product information

5.1 Type key
Example: TM 32/8 -10M
TMW 32/11 HD
TM Submersible pump
W W = with whirl system (TWISTER function)
R = low suction version
32 Nominal diameter of pressure port [mm]:
32 = Rp 1¼
/8 Max. delivery head [m] when Q = 0m³/h
HD For aggressive water
(material 1.4435 (AISI316L))
10M Length of mains connecting cable [m]: 10
WILO SE 10/2009