Perpetual Calendar; Flyback Chronograph - Baume And Mercier Clifton Bedienungsanleitung

Setting the moon
4. Press the corrector button (C4), until the full moon
appears in the center of the moon phase aperture (I).
5. Then press the corrector button (C4) as many times as
there are days passed since the last full moon (consult a
calendar).
To know the dates of the full moon and set your watch, please
visit our website www.baume-et-mercier.com and consult the
page corresponding to your model.
Date change
6. Press the corrector button (C3), until the date hand (E) is
positioned on the 1.
Setting the month
7. Press the corrector button (C2) to advance the month (M)
until the desired month.
Setting the date
8. Press the corrector button (C3) to advance the date (E) to
the desired date.
Setting the day of the week
9. Press the corrector button (C1), to advance the day (K) to
the desired day.
Setting the time
10. Turn the crown to advance the hands (A, B) clockwise
and position them at the desired time.
11. When the start of the set time is announced (reference
clock, radio, etc.), reset the crown to Position 1.
For months with fewer than 31 days, it is necessary to
change the date manually at the end of the month.
10 |

PERPETUAL CALENDAR

19
Warning: In order to avoid jamming the corrector buttons
or damaging the movement, it is extremely important that
you do not make any adjustments (day, date, month and
moon phase) between 8 p.m. and 1 a.m.
To manipulate the corrector buttons, use the small tool
provided in the watch packaging. To adjust your watch,
please ensure it is fully wound and then respect the following
steps in this specific order.
Initial pre-setting stage
1. Pull the crown to Position 2, the seconds hand (C) will
stop moving.
2. Turn the crown to advance the hands (A, B) clockwise
until the date (E) and day (K) change (when the watch
indicates midnight).
3. Continue to turn the crown to set the hands to 3 a.m.
Setting the moon
4. Press the corrector button (C4), until the full moon
appears in the center of the moon phase aperture (I).
5. Then press the corrector button (C4) as many times as
there are days passed since the last full moon (consult a
calendar).
To know the dates of the full moon and set your watch, please
visit our website www.baume-et-mercier.com and consult the
page corresponding to your model.
Date change
6. Press the corrector button (C3) until the date hand (E) is
positioned on the 1.
Setting the month and the year in the leap-year cycle
7. Press the corrector button (C2) until the desired month
(M) and position of the year (Y) in the leap-year cycle
are indicated.
Note: the position 4 corresponds to the leap years that occur
every 4 years. Thus, as 2016 was a leap year, the Y hand must
be positioned on 1 if you set your watch in 2017, on 2 in 2018,
on 3 in 2019 then on 4 in 2020 which is the next leap year.
Setting the date
8. Press the corrector button (C3) to advance the date (E) to
the desired date.
Setting the day of the week
9. Press the corrector button (C1) to advance the day (K) to
the desired day.
Setting the time
10. Turn the crown to advance the hands (A, B) clockwise and
position them at the desired time.
11. On the hourly time signal (reference clock, radio, etc.),
reset the crown back in to Position 1.
SIMPLE CHRONOGRAPH
20 21 23 25 26 28 29
P1: S t a r t /s top pu sh - but ton . P re s s onc e to s t a r t t he
chronog raph (F=seconds, G =minutes, H=hours).
Press a second time to stop and a third time to start the
chronograph again.
P2: Reset push-button. Once the chronograph has been
stopped by pressing the P1 push-button, press the P2 to
reset all counters to zero.
To measure several successive times, without counting
i n t e r v a l s , p r e s s t h e P 1 p u s h - b u t t o n s e v e r a l t i m e s
consecutively, as follows:
1. Start.
2. Stop and read.
3. Start.
4. Stop and read.
This operation may be repeated as often as desired to
measure successive times.
5. Press the P2 push-button to reset the chronograph to zero.

FLYBACK CHRONOGRAPH

22
1. Start the chronograph by pressing the push-button P1.
2. To move directly to the next sequence, press the P2 push-
button which will reset the chronograph and start it
immediately for a new measurement.
Note : It is also possible to use the standard Chronograph
function. To do this, refer to the preceding paragraph Simple
Chronograph.
DUAL TIME WITH CHRONOGRAPH
24
To use the Chronograph function, refer to the preceding
paragraph Simple Chronograph.
Setting the second time zone
1. Pull the crown in Position 2.
2. Turn the crown clockwise to advance the second time
zone hand (D) and set it at the desired time.
| 11